| /*- |
| * Copyright 2021 Intel Corp |
| * Copyright 2021 Rubicon Communications, LLC (Netgate) |
| * SPDX-License-Identifier: BSD-3-Clause |
| */ |
| |
| // clang-format off |
| #include "igc_api.h" |
| |
| static void igc_config_collision_dist_generic(struct igc_hw *hw); |
| |
| /** |
| * igc_init_mac_ops_generic - Initialize MAC function pointers |
| * @hw: pointer to the HW structure |
| * |
| * Setups up the function pointers to no-op functions |
| **/ |
| void igc_init_mac_ops_generic(struct igc_hw *hw) |
| { |
| struct igc_mac_info *mac = &hw->mac; |
| DEBUGFUNC("igc_init_mac_ops_generic"); |
| |
| /* General Setup */ |
| mac->ops.init_params = igc_null_ops_generic; |
| mac->ops.config_collision_dist = igc_config_collision_dist_generic; |
| mac->ops.rar_set = igc_rar_set_generic; |
| } |
| |
| /** |
| * igc_null_ops_generic - No-op function, returns 0 |
| * @hw: pointer to the HW structure |
| **/ |
| s32 igc_null_ops_generic(struct igc_hw IGC_UNUSEDARG *hw) |
| { |
| DEBUGFUNC("igc_null_ops_generic"); |
| return IGC_SUCCESS; |
| } |
| |
| /** |
| * igc_null_mac_generic - No-op function, return void |
| * @hw: pointer to the HW structure |
| **/ |
| void igc_null_mac_generic(struct igc_hw IGC_UNUSEDARG *hw) |
| { |
| DEBUGFUNC("igc_null_mac_generic"); |
| return; |
| } |
| |
| /** |
| * igc_null_link_info - No-op function, return 0 |
| * @hw: pointer to the HW structure |
| * @s: dummy variable |
| * @d: dummy variable |
| **/ |
| s32 igc_null_link_info(struct igc_hw IGC_UNUSEDARG *hw, |
| u16 IGC_UNUSEDARG *s, u16 IGC_UNUSEDARG *d) |
| { |
| DEBUGFUNC("igc_null_link_info"); |
| return IGC_SUCCESS; |
| } |
| |
| /** |
| * igc_null_mng_mode - No-op function, return false |
| * @hw: pointer to the HW structure |
| **/ |
| bool igc_null_mng_mode(struct igc_hw IGC_UNUSEDARG *hw) |
| { |
| DEBUGFUNC("igc_null_mng_mode"); |
| return false; |
| } |
| |
| /** |
| * igc_null_update_mc - No-op function, return void |
| * @hw: pointer to the HW structure |
| * @h: dummy variable |
| * @a: dummy variable |
| **/ |
| void igc_null_update_mc(struct igc_hw IGC_UNUSEDARG *hw, |
| u8 IGC_UNUSEDARG *h, u32 IGC_UNUSEDARG a) |
| { |
| DEBUGFUNC("igc_null_update_mc"); |
| return; |
| } |
| |
| /** |
| * igc_null_write_vfta - No-op function, return void |
| * @hw: pointer to the HW structure |
| * @a: dummy variable |
| * @b: dummy variable |
| **/ |
| void igc_null_write_vfta(struct igc_hw IGC_UNUSEDARG *hw, |
| u32 IGC_UNUSEDARG a, u32 IGC_UNUSEDARG b) |
| { |
| DEBUGFUNC("igc_null_write_vfta"); |
| return; |
| } |
| |
| /** |
| * igc_null_rar_set - No-op function, return 0 |
| * @hw: pointer to the HW structure |
| * @h: dummy variable |
| * @a: dummy variable |
| **/ |
| int igc_null_rar_set(struct igc_hw IGC_UNUSEDARG *hw, |
| u8 IGC_UNUSEDARG *h, u32 IGC_UNUSEDARG a) |
| { |
| DEBUGFUNC("igc_null_rar_set"); |
| return IGC_SUCCESS; |
| } |
| |
| /** |
| * igc_set_lan_id_single_port - Set LAN id for a single port device |
| * @hw: pointer to the HW structure |
| * |
| * Sets the LAN function id to zero for a single port device. |
| **/ |
| void igc_set_lan_id_single_port(struct igc_hw *hw) |
| { |
| struct igc_bus_info *bus = &hw->bus; |
| |
| bus->func = 0; |
| } |
| |
| /** |
| * igc_clear_vfta_generic - Clear VLAN filter table |
| * @hw: pointer to the HW structure |
| * |
| * Clears the register array which contains the VLAN filter table by |
| * setting all the values to 0. |
| **/ |
| void igc_clear_vfta_generic(struct igc_hw *hw) |
| { |
| u32 offset; |
| |
| DEBUGFUNC("igc_clear_vfta_generic"); |
| |
| for (offset = 0; offset < IGC_VLAN_FILTER_TBL_SIZE; offset++) { |
| IGC_WRITE_REG_ARRAY(hw, IGC_VFTA, offset, 0); |
| IGC_WRITE_FLUSH(hw); |
| } |
| } |
| |
| /** |
| * igc_write_vfta_generic - Write value to VLAN filter table |
| * @hw: pointer to the HW structure |
| * @offset: register offset in VLAN filter table |
| * @value: register value written to VLAN filter table |
| * |
| * Writes value at the given offset in the register array which stores |
| * the VLAN filter table. |
| **/ |
| void igc_write_vfta_generic(struct igc_hw *hw, u32 offset, u32 value) |
| { |
| DEBUGFUNC("igc_write_vfta_generic"); |
| |
| IGC_WRITE_REG_ARRAY(hw, IGC_VFTA, offset, value); |
| IGC_WRITE_FLUSH(hw); |
| } |
| |
| /** |
| * igc_init_rx_addrs_generic - Initialize receive address's |
| * @hw: pointer to the HW structure |
| * @rar_count: receive address registers |
| * |
| * Setup the receive address registers by setting the base receive address |
| * register to the devices MAC address and clearing all the other receive |
| * address registers to 0. |
| **/ |
| void igc_init_rx_addrs_generic(struct igc_hw *hw, u16 rar_count) |
| { |
| u32 i; |
| u8 mac_addr[ETH_ADDR_LEN] = {0}; |
| |
| DEBUGFUNC("igc_init_rx_addrs_generic"); |
| |
| /* Setup the receive address */ |
| DEBUGOUT("Programming MAC Address into RAR[0]\n"); |
| |
| hw->mac.ops.rar_set(hw, hw->mac.addr, 0); |
| |
| /* Zero out the other (rar_entry_count - 1) receive addresses */ |
| DEBUGOUT1("Clearing RAR[1-%u]\n", rar_count-1); |
| for (i = 1; i < rar_count; i++) |
| hw->mac.ops.rar_set(hw, mac_addr, i); |
| } |
| |
| /** |
| * igc_check_alt_mac_addr_generic - Check for alternate MAC addr |
| * @hw: pointer to the HW structure |
| * |
| * Checks the nvm for an alternate MAC address. An alternate MAC address |
| * can be setup by pre-boot software and must be treated like a permanent |
| * address and must override the actual permanent MAC address. If an |
| * alternate MAC address is found it is programmed into RAR0, replacing |
| * the permanent address that was installed into RAR0 by the Si on reset. |
| * This function will return SUCCESS unless it encounters an error while |
| * reading the EEPROM. |
| **/ |
| s32 igc_check_alt_mac_addr_generic(struct igc_hw *hw) |
| { |
| u32 i; |
| s32 ret_val; |
| u16 offset, nvm_alt_mac_addr_offset, nvm_data; |
| u8 alt_mac_addr[ETH_ADDR_LEN]; |
| |
| DEBUGFUNC("igc_check_alt_mac_addr_generic"); |
| |
| ret_val = hw->nvm.ops.read(hw, NVM_COMPAT, 1, &nvm_data); |
| if (ret_val) |
| return ret_val; |
| |
| |
| ret_val = hw->nvm.ops.read(hw, NVM_ALT_MAC_ADDR_PTR, 1, |
| &nvm_alt_mac_addr_offset); |
| if (ret_val) { |
| DEBUGOUT("NVM Read Error\n"); |
| return ret_val; |
| } |
| |
| if ((nvm_alt_mac_addr_offset == 0xFFFF) || |
| (nvm_alt_mac_addr_offset == 0x0000)) |
| /* There is no Alternate MAC Address */ |
| return IGC_SUCCESS; |
| |
| if (hw->bus.func == IGC_FUNC_1) |
| nvm_alt_mac_addr_offset += IGC_ALT_MAC_ADDRESS_OFFSET_LAN1; |
| for (i = 0; i < ETH_ADDR_LEN; i += 2) { |
| offset = u16(nvm_alt_mac_addr_offset + (i >> 1)); |
| ret_val = hw->nvm.ops.read(hw, offset, 1, &nvm_data); |
| if (ret_val) { |
| DEBUGOUT("NVM Read Error\n"); |
| return ret_val; |
| } |
| |
| alt_mac_addr[i] = (u8)(nvm_data & 0xFF); |
| alt_mac_addr[i + 1] = (u8)(nvm_data >> 8); |
| } |
| |
| /* if multicast bit is set, the alternate address will not be used */ |
| if (alt_mac_addr[0] & 0x01) { |
| DEBUGOUT("Ignoring Alternate Mac Address with MC bit set\n"); |
| return IGC_SUCCESS; |
| } |
| |
| /* We have a valid alternate MAC address, and we want to treat it the |
| * same as the normal permanent MAC address stored by the HW into the |
| * RAR. Do this by mapping this address into RAR0. |
| */ |
| hw->mac.ops.rar_set(hw, alt_mac_addr, 0); |
| |
| return IGC_SUCCESS; |
| } |
| |
| /** |
| * igc_rar_set_generic - Set receive address register |
| * @hw: pointer to the HW structure |
| * @addr: pointer to the receive address |
| * @index: receive address array register |
| * |
| * Sets the receive address array register at index to the address passed |
| * in by addr. |
| **/ |
| int igc_rar_set_generic(struct igc_hw *hw, u8 *addr, u32 index) |
| { |
| u32 rar_low, rar_high; |
| |
| DEBUGFUNC("igc_rar_set_generic"); |
| |
| /* HW expects these in little endian so we reverse the byte order |
| * from network order (big endian) to little endian |
| */ |
| rar_low = ((u32) addr[0] | ((u32) addr[1] << 8) | |
| ((u32) addr[2] << 16) | ((u32) addr[3] << 24)); |
| |
| rar_high = ((u32) addr[4] | ((u32) addr[5] << 8)); |
| |
| /* If MAC address zero, no need to set the AV bit */ |
| if (rar_low || rar_high) |
| rar_high |= IGC_RAH_AV; |
| |
| /* Some bridges will combine consecutive 32-bit writes into |
| * a single burst write, which will malfunction on some parts. |
| * The flushes avoid this. |
| */ |
| IGC_WRITE_REG(hw, IGC_RAL(index), rar_low); |
| IGC_WRITE_FLUSH(hw); |
| IGC_WRITE_REG(hw, IGC_RAH(index), rar_high); |
| IGC_WRITE_FLUSH(hw); |
| |
| return IGC_SUCCESS; |
| } |
| |
| /** |
| * igc_hash_mc_addr_generic - Generate a multicast hash value |
| * @hw: pointer to the HW structure |
| * @mc_addr: pointer to a multicast address |
| * |
| * Generates a multicast address hash value which is used to determine |
| * the multicast filter table array address and new table value. |
| **/ |
| u32 igc_hash_mc_addr_generic(struct igc_hw *hw, u8 *mc_addr) |
| { |
| u32 hash_value, hash_mask; |
| u8 bit_shift = 0; |
| |
| DEBUGFUNC("igc_hash_mc_addr_generic"); |
| |
| /* Register count multiplied by bits per register */ |
| hash_mask = (hw->mac.mta_reg_count * 32) - 1; |
| |
| /* For a mc_filter_type of 0, bit_shift is the number of left-shifts |
| * where 0xFF would still fall within the hash mask. |
| */ |
| while (hash_mask >> bit_shift != 0xFF) |
| bit_shift++; |
| |
| /* The portion of the address that is used for the hash table |
| * is determined by the mc_filter_type setting. |
| * The algorithm is such that there is a total of 8 bits of shifting. |
| * The bit_shift for a mc_filter_type of 0 represents the number of |
| * left-shifts where the MSB of mc_addr[5] would still fall within |
| * the hash_mask. Case 0 does this exactly. Since there are a total |
| * of 8 bits of shifting, then mc_addr[4] will shift right the |
| * remaining number of bits. Thus 8 - bit_shift. The rest of the |
| * cases are a variation of this algorithm...essentially raising the |
| * number of bits to shift mc_addr[5] left, while still keeping the |
| * 8-bit shifting total. |
| * |
| * For example, given the following Destination MAC Address and an |
| * mta register count of 128 (thus a 4096-bit vector and 0xFFF mask), |
| * we can see that the bit_shift for case 0 is 4. These are the hash |
| * values resulting from each mc_filter_type... |
| * [0] [1] [2] [3] [4] [5] |
| * 01 AA 00 12 34 56 |
| * LSB MSB |
| * |
| * case 0: hash_value = ((0x34 >> 4) | (0x56 << 4)) & 0xFFF = 0x563 |
| * case 1: hash_value = ((0x34 >> 3) | (0x56 << 5)) & 0xFFF = 0xAC6 |
| * case 2: hash_value = ((0x34 >> 2) | (0x56 << 6)) & 0xFFF = 0x163 |
| * case 3: hash_value = ((0x34 >> 0) | (0x56 << 8)) & 0xFFF = 0x634 |
| */ |
| switch (hw->mac.mc_filter_type) { |
| default: |
| case 0: |
| break; |
| case 1: |
| bit_shift += 1; |
| break; |
| case 2: |
| bit_shift += 2; |
| break; |
| case 3: |
| bit_shift += 4; |
| break; |
| } |
| |
| hash_value = hash_mask & (((mc_addr[4] >> (8 - bit_shift)) | |
| (((u16) mc_addr[5]) << bit_shift))); |
| |
| return hash_value; |
| } |
| |
| /** |
| * igc_update_mc_addr_list_generic - Update Multicast addresses |
| * @hw: pointer to the HW structure |
| * @mc_addr_list: array of multicast addresses to program |
| * @mc_addr_count: number of multicast addresses to program |
| * |
| * Updates entire Multicast Table Array. |
| * The caller must have a packed mc_addr_list of multicast addresses. |
| **/ |
| void igc_update_mc_addr_list_generic(struct igc_hw *hw, |
| u8 *mc_addr_list, u32 mc_addr_count) |
| { |
| u32 hash_value, hash_bit, hash_reg; |
| int i; |
| |
| DEBUGFUNC("igc_update_mc_addr_list_generic"); |
| |
| /* clear mta_shadow */ |
| memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow)); |
| |
| /* update mta_shadow from mc_addr_list */ |
| for (i = 0; (u32) i < mc_addr_count; i++) { |
| hash_value = igc_hash_mc_addr_generic(hw, mc_addr_list); |
| |
| hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1); |
| hash_bit = hash_value & 0x1F; |
| |
| hw->mac.mta_shadow[hash_reg] |= (1 << hash_bit); |
| mc_addr_list += (ETH_ADDR_LEN); |
| } |
| |
| /* replace the entire MTA table */ |
| for (i = hw->mac.mta_reg_count - 1; i >= 0; i--) |
| IGC_WRITE_REG_ARRAY(hw, IGC_MTA, i, hw->mac.mta_shadow[i]); |
| IGC_WRITE_FLUSH(hw); |
| } |
| |
| /** |
| * igc_clear_hw_cntrs_base_generic - Clear base hardware counters |
| * @hw: pointer to the HW structure |
| * |
| * Clears the base hardware counters by reading the counter registers. |
| **/ |
| void igc_clear_hw_cntrs_base_generic(struct igc_hw *hw) |
| { |
| DEBUGFUNC("igc_clear_hw_cntrs_base_generic"); |
| |
| IGC_READ_REG(hw, IGC_CRCERRS); |
| IGC_READ_REG(hw, IGC_MPC); |
| IGC_READ_REG(hw, IGC_SCC); |
| IGC_READ_REG(hw, IGC_ECOL); |
| IGC_READ_REG(hw, IGC_MCC); |
| IGC_READ_REG(hw, IGC_LATECOL); |
| IGC_READ_REG(hw, IGC_COLC); |
| IGC_READ_REG(hw, IGC_RERC); |
| IGC_READ_REG(hw, IGC_DC); |
| IGC_READ_REG(hw, IGC_RLEC); |
| IGC_READ_REG(hw, IGC_XONRXC); |
| IGC_READ_REG(hw, IGC_XONTXC); |
| IGC_READ_REG(hw, IGC_XOFFRXC); |
| IGC_READ_REG(hw, IGC_XOFFTXC); |
| IGC_READ_REG(hw, IGC_FCRUC); |
| IGC_READ_REG(hw, IGC_GPRC); |
| IGC_READ_REG(hw, IGC_BPRC); |
| IGC_READ_REG(hw, IGC_MPRC); |
| IGC_READ_REG(hw, IGC_GPTC); |
| IGC_READ_REG(hw, IGC_GORCL); |
| IGC_READ_REG(hw, IGC_GORCH); |
| IGC_READ_REG(hw, IGC_GOTCL); |
| IGC_READ_REG(hw, IGC_GOTCH); |
| IGC_READ_REG(hw, IGC_RNBC); |
| IGC_READ_REG(hw, IGC_RUC); |
| IGC_READ_REG(hw, IGC_RFC); |
| IGC_READ_REG(hw, IGC_ROC); |
| IGC_READ_REG(hw, IGC_RJC); |
| IGC_READ_REG(hw, IGC_TORL); |
| IGC_READ_REG(hw, IGC_TORH); |
| IGC_READ_REG(hw, IGC_TOTL); |
| IGC_READ_REG(hw, IGC_TOTH); |
| IGC_READ_REG(hw, IGC_TPR); |
| IGC_READ_REG(hw, IGC_TPT); |
| IGC_READ_REG(hw, IGC_MPTC); |
| IGC_READ_REG(hw, IGC_BPTC); |
| IGC_READ_REG(hw, IGC_TLPIC); |
| IGC_READ_REG(hw, IGC_RLPIC); |
| IGC_READ_REG(hw, IGC_RXDMTC); |
| } |
| |
| /** |
| * igc_check_for_copper_link_generic - Check for link (Copper) |
| * @hw: pointer to the HW structure |
| * |
| * Checks to see of the link status of the hardware has changed. If a |
| * change in link status has been detected, then we read the PHY registers |
| * to get the current speed/duplex if link exists. |
| **/ |
| s32 igc_check_for_copper_link_generic(struct igc_hw *hw) |
| { |
| struct igc_mac_info *mac = &hw->mac; |
| s32 ret_val; |
| bool link = false; |
| |
| DEBUGFUNC("igc_check_for_copper_link"); |
| |
| /* We only want to go out to the PHY registers to see if Auto-Neg |
| * has completed and/or if our link status has changed. The |
| * get_link_status flag is set upon receiving a Link Status |
| * Change or Rx Sequence Error interrupt. |
| */ |
| if (!mac->get_link_status) |
| return IGC_SUCCESS; |
| |
| /* First we want to see if the MII Status Register reports |
| * link. If so, then we want to get the current speed/duplex |
| * of the PHY. |
| */ |
| ret_val = igc_phy_has_link_generic(hw, 1, 0, &link); |
| if (ret_val) |
| return ret_val; |
| |
| if (!link) |
| return IGC_SUCCESS; /* No link detected */ |
| |
| mac->get_link_status = false; |
| |
| /* Check if there was DownShift, must be checked |
| * immediately after link-up |
| */ |
| igc_check_downshift_generic(hw); |
| |
| /* If we are forcing speed/duplex, then we simply return since |
| * we have already determined whether we have link or not. |
| */ |
| if (!mac->autoneg) |
| return -IGC_ERR_CONFIG; |
| |
| /* Auto-Neg is enabled. Auto Speed Detection takes care |
| * of MAC speed/duplex configuration. So we only need to |
| * configure Collision Distance in the MAC. |
| */ |
| mac->ops.config_collision_dist(hw); |
| |
| /* Configure Flow Control now that Auto-Neg has completed. |
| * First, we need to restore the desired flow control |
| * settings because we may have had to re-autoneg with a |
| * different link partner. |
| */ |
| ret_val = igc_config_fc_after_link_up_generic(hw); |
| if (ret_val) |
| DEBUGOUT("Error configuring flow control\n"); |
| |
| return ret_val; |
| } |
| |
| /** |
| * igc_setup_link_generic - Setup flow control and link settings |
| * @hw: pointer to the HW structure |
| * |
| * Determines which flow control settings to use, then configures flow |
| * control. Calls the appropriate media-specific link configuration |
| * function. Assuming the adapter has a valid link partner, a valid link |
| * should be established. Assumes the hardware has previously been reset |
| * and the transmitter and receiver are not enabled. |
| **/ |
| s32 igc_setup_link_generic(struct igc_hw *hw) |
| { |
| s32 ret_val; |
| |
| DEBUGFUNC("igc_setup_link_generic"); |
| |
| /* In the case of the phy reset being blocked, we already have a link. |
| * We do not need to set it up again. |
| */ |
| if (hw->phy.ops.check_reset_block && hw->phy.ops.check_reset_block(hw)) |
| return IGC_SUCCESS; |
| |
| /* If requested flow control is set to default, set flow control |
| * for both 'rx' and 'tx' pause frames. |
| */ |
| if (hw->fc.requested_mode == igc_fc_default) { |
| hw->fc.requested_mode = igc_fc_full; |
| } |
| |
| /* Save off the requested flow control mode for use later. Depending |
| * on the link partner's capabilities, we may or may not use this mode. |
| */ |
| hw->fc.current_mode = hw->fc.requested_mode; |
| |
| DEBUGOUT1("After fix-ups FlowControl is now = %x\n", |
| hw->fc.current_mode); |
| |
| /* Call the necessary media_type subroutine to configure the link. */ |
| ret_val = hw->mac.ops.setup_physical_interface(hw); |
| if (ret_val) |
| return ret_val; |
| |
| /* Initialize the flow control address, type, and PAUSE timer |
| * registers to their default values. This is done even if flow |
| * control is disabled, because it does not hurt anything to |
| * initialize these registers. |
| */ |
| DEBUGOUT("Initializing the Flow Control address, type and timer regs\n"); |
| IGC_WRITE_REG(hw, IGC_FCT, FLOW_CONTROL_TYPE); |
| IGC_WRITE_REG(hw, IGC_FCAH, FLOW_CONTROL_ADDRESS_HIGH); |
| IGC_WRITE_REG(hw, IGC_FCAL, FLOW_CONTROL_ADDRESS_LOW); |
| |
| IGC_WRITE_REG(hw, IGC_FCTTV, hw->fc.pause_time); |
| |
| return igc_set_fc_watermarks_generic(hw); |
| } |
| |
| /** |
| * igc_config_collision_dist_generic - Configure collision distance |
| * @hw: pointer to the HW structure |
| * |
| * Configures the collision distance to the default value and is used |
| * during link setup. |
| **/ |
| static void igc_config_collision_dist_generic(struct igc_hw *hw) |
| { |
| u32 tctl; |
| |
| DEBUGFUNC("igc_config_collision_dist_generic"); |
| |
| tctl = IGC_READ_REG(hw, IGC_TCTL); |
| |
| tctl &= ~IGC_TCTL_COLD; |
| tctl |= IGC_COLLISION_DISTANCE << IGC_COLD_SHIFT; |
| |
| IGC_WRITE_REG(hw, IGC_TCTL, tctl); |
| IGC_WRITE_FLUSH(hw); |
| } |
| |
| /** |
| * igc_set_fc_watermarks_generic - Set flow control high/low watermarks |
| * @hw: pointer to the HW structure |
| * |
| * Sets the flow control high/low threshold (watermark) registers. If |
| * flow control XON frame transmission is enabled, then set XON frame |
| * transmission as well. |
| **/ |
| s32 igc_set_fc_watermarks_generic(struct igc_hw *hw) |
| { |
| u32 fcrtl = 0, fcrth = 0; |
| |
| DEBUGFUNC("igc_set_fc_watermarks_generic"); |
| |
| /* Set the flow control receive threshold registers. Normally, |
| * these registers will be set to a default threshold that may be |
| * adjusted later by the driver's runtime code. However, if the |
| * ability to transmit pause frames is not enabled, then these |
| * registers will be set to 0. |
| */ |
| if (hw->fc.current_mode & igc_fc_tx_pause) { |
| /* We need to set up the Receive Threshold high and low water |
| * marks as well as (optionally) enabling the transmission of |
| * XON frames. |
| */ |
| fcrtl = hw->fc.low_water; |
| if (hw->fc.send_xon) |
| fcrtl |= IGC_FCRTL_XONE; |
| |
| fcrth = hw->fc.high_water; |
| } |
| IGC_WRITE_REG(hw, IGC_FCRTL, fcrtl); |
| IGC_WRITE_REG(hw, IGC_FCRTH, fcrth); |
| |
| return IGC_SUCCESS; |
| } |
| |
| /** |
| * igc_force_mac_fc_generic - Force the MAC's flow control settings |
| * @hw: pointer to the HW structure |
| * |
| * Force the MAC's flow control settings. Sets the TFCE and RFCE bits in the |
| * device control register to reflect the adapter settings. TFCE and RFCE |
| * need to be explicitly set by software when a copper PHY is used because |
| * autonegotiation is managed by the PHY rather than the MAC. Software must |
| * also configure these bits when link is forced on a fiber connection. |
| **/ |
| s32 igc_force_mac_fc_generic(struct igc_hw *hw) |
| { |
| u32 ctrl; |
| |
| DEBUGFUNC("igc_force_mac_fc_generic"); |
| |
| ctrl = IGC_READ_REG(hw, IGC_CTRL); |
| |
| /* Because we didn't get link via the internal auto-negotiation |
| * mechanism (we either forced link or we got link via PHY |
| * auto-neg), we have to manually enable/disable transmit an |
| * receive flow control. |
| * |
| * The "Case" statement below enables/disable flow control |
| * according to the "hw->fc.current_mode" parameter. |
| * |
| * The possible values of the "fc" parameter are: |
| * 0: Flow control is completely disabled |
| * 1: Rx flow control is enabled (we can receive pause |
| * frames but not send pause frames). |
| * 2: Tx flow control is enabled (we can send pause frames |
| * frames but we do not receive pause frames). |
| * 3: Both Rx and Tx flow control (symmetric) is enabled. |
| * other: No other values should be possible at this point. |
| */ |
| DEBUGOUT1("hw->fc.current_mode = %u\n", hw->fc.current_mode); |
| |
| switch (hw->fc.current_mode) { |
| case igc_fc_none: |
| ctrl &= (~(IGC_CTRL_TFCE | IGC_CTRL_RFCE)); |
| break; |
| case igc_fc_rx_pause: |
| ctrl &= (~IGC_CTRL_TFCE); |
| ctrl |= IGC_CTRL_RFCE; |
| break; |
| case igc_fc_tx_pause: |
| ctrl &= (~IGC_CTRL_RFCE); |
| ctrl |= IGC_CTRL_TFCE; |
| break; |
| case igc_fc_full: |
| ctrl |= (IGC_CTRL_TFCE | IGC_CTRL_RFCE); |
| break; |
| default: |
| DEBUGOUT("Flow control param set incorrectly\n"); |
| return -IGC_ERR_CONFIG; |
| } |
| |
| IGC_WRITE_REG(hw, IGC_CTRL, ctrl); |
| |
| return IGC_SUCCESS; |
| } |
| |
| /** |
| * igc_config_fc_after_link_up_generic - Configures flow control after link |
| * @hw: pointer to the HW structure |
| * |
| * Checks the status of auto-negotiation after link up to ensure that the |
| * speed and duplex were not forced. If the link needed to be forced, then |
| * flow control needs to be forced also. If auto-negotiation is enabled |
| * and did not fail, then we configure flow control based on our link |
| * partner. |
| **/ |
| s32 igc_config_fc_after_link_up_generic(struct igc_hw *hw) |
| { |
| struct igc_mac_info *mac = &hw->mac; |
| s32 ret_val = IGC_SUCCESS; |
| u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg; |
| u16 speed, duplex; |
| |
| DEBUGFUNC("igc_config_fc_after_link_up_generic"); |
| |
| if (ret_val) { |
| DEBUGOUT("Error forcing flow control settings\n"); |
| return ret_val; |
| } |
| |
| /* Check for the case where we have copper media and auto-neg is |
| * enabled. In this case, we need to check and see if Auto-Neg |
| * has completed, and if so, how the PHY and link partner has |
| * flow control configured. |
| */ |
| if (mac->autoneg) { |
| /* Read the MII Status Register and check to see if AutoNeg |
| * has completed. We read this twice because this reg has |
| * some "sticky" (latched) bits. |
| */ |
| ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &mii_status_reg); |
| if (ret_val) |
| return ret_val; |
| ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &mii_status_reg); |
| if (ret_val) |
| return ret_val; |
| |
| if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) { |
| DEBUGOUT("Copper PHY and Auto Neg has not completed.\n"); |
| return ret_val; |
| } |
| |
| /* The AutoNeg process has completed, so we now need to |
| * read both the Auto Negotiation Advertisement |
| * Register (Address 4) and the Auto_Negotiation Base |
| * Page Ability Register (Address 5) to determine how |
| * flow control was negotiated. |
| */ |
| ret_val = hw->phy.ops.read_reg(hw, PHY_AUTONEG_ADV, |
| &mii_nway_adv_reg); |
| if (ret_val) |
| return ret_val; |
| ret_val = hw->phy.ops.read_reg(hw, PHY_LP_ABILITY, |
| &mii_nway_lp_ability_reg); |
| if (ret_val) |
| return ret_val; |
| |
| /* Two bits in the Auto Negotiation Advertisement Register |
| * (Address 4) and two bits in the Auto Negotiation Base |
| * Page Ability Register (Address 5) determine flow control |
| * for both the PHY and the link partner. The following |
| * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, |
| * 1999, describes these PAUSE resolution bits and how flow |
| * control is determined based upon these settings. |
| * NOTE: DC = Don't Care |
| * |
| * LOCAL DEVICE | LINK PARTNER |
| * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution |
| *-------|---------|-------|---------|-------------------- |
| * 0 | 0 | DC | DC | igc_fc_none |
| * 0 | 1 | 0 | DC | igc_fc_none |
| * 0 | 1 | 1 | 0 | igc_fc_none |
| * 0 | 1 | 1 | 1 | igc_fc_tx_pause |
| * 1 | 0 | 0 | DC | igc_fc_none |
| * 1 | DC | 1 | DC | igc_fc_full |
| * 1 | 1 | 0 | 0 | igc_fc_none |
| * 1 | 1 | 0 | 1 | igc_fc_rx_pause |
| * |
| * Are both PAUSE bits set to 1? If so, this implies |
| * Symmetric Flow Control is enabled at both ends. The |
| * ASM_DIR bits are irrelevant per the spec. |
| * |
| * For Symmetric Flow Control: |
| * |
| * LOCAL DEVICE | LINK PARTNER |
| * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result |
| *-------|---------|-------|---------|-------------------- |
| * 1 | DC | 1 | DC | IGC_fc_full |
| * |
| */ |
| if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && |
| (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { |
| /* Now we need to check if the user selected Rx ONLY |
| * of pause frames. In this case, we had to advertise |
| * FULL flow control because we could not advertise Rx |
| * ONLY. Hence, we must now check to see if we need to |
| * turn OFF the TRANSMISSION of PAUSE frames. |
| */ |
| if (hw->fc.requested_mode == igc_fc_full) { |
| hw->fc.current_mode = igc_fc_full; |
| DEBUGOUT("Flow Control = FULL.\n"); |
| } else { |
| hw->fc.current_mode = igc_fc_rx_pause; |
| DEBUGOUT("Flow Control = Rx PAUSE frames only.\n"); |
| } |
| } |
| /* For receiving PAUSE frames ONLY. |
| * |
| * LOCAL DEVICE | LINK PARTNER |
| * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result |
| *-------|---------|-------|---------|-------------------- |
| * 0 | 1 | 1 | 1 | igc_fc_tx_pause |
| */ |
| else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && |
| (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && |
| (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && |
| (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { |
| hw->fc.current_mode = igc_fc_tx_pause; |
| DEBUGOUT("Flow Control = Tx PAUSE frames only.\n"); |
| } |
| /* For transmitting PAUSE frames ONLY. |
| * |
| * LOCAL DEVICE | LINK PARTNER |
| * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result |
| *-------|---------|-------|---------|-------------------- |
| * 1 | 1 | 0 | 1 | igc_fc_rx_pause |
| */ |
| else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && |
| (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && |
| !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && |
| (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { |
| hw->fc.current_mode = igc_fc_rx_pause; |
| DEBUGOUT("Flow Control = Rx PAUSE frames only.\n"); |
| } else { |
| /* Per the IEEE spec, at this point flow control |
| * should be disabled. |
| */ |
| hw->fc.current_mode = igc_fc_none; |
| DEBUGOUT("Flow Control = NONE.\n"); |
| } |
| |
| /* Now we need to do one last check... If we auto- |
| * negotiated to HALF DUPLEX, flow control should not be |
| * enabled per IEEE 802.3 spec. |
| */ |
| ret_val = mac->ops.get_link_up_info(hw, &speed, &duplex); |
| if (ret_val) { |
| DEBUGOUT("Error getting link speed and duplex\n"); |
| return ret_val; |
| } |
| |
| if (duplex == HALF_DUPLEX) |
| hw->fc.current_mode = igc_fc_none; |
| |
| /* Now we call a subroutine to actually force the MAC |
| * controller to use the correct flow control settings. |
| */ |
| ret_val = igc_force_mac_fc_generic(hw); |
| if (ret_val) { |
| DEBUGOUT("Error forcing flow control settings\n"); |
| return ret_val; |
| } |
| } |
| |
| return IGC_SUCCESS; |
| } |
| |
| /** |
| * igc_get_speed_and_duplex_copper_generic - Retrieve current speed/duplex |
| * @hw: pointer to the HW structure |
| * @speed: stores the current speed |
| * @duplex: stores the current duplex |
| * |
| * Read the status register for the current speed/duplex and store the current |
| * speed and duplex for copper connections. |
| **/ |
| s32 igc_get_speed_and_duplex_copper_generic(struct igc_hw *hw, u16 *speed, |
| u16 *duplex) |
| { |
| u32 status; |
| |
| DEBUGFUNC("igc_get_speed_and_duplex_copper_generic"); |
| |
| status = IGC_READ_REG(hw, IGC_STATUS); |
| if (status & IGC_STATUS_SPEED_1000) { |
| /* For I225, STATUS will indicate 1G speed in both 1 Gbps |
| * and 2.5 Gbps link modes. An additional bit is used |
| * to differentiate between 1 Gbps and 2.5 Gbps. |
| */ |
| if ((hw->mac.type == igc_i225) && |
| (status & IGC_STATUS_SPEED_2500)) { |
| *speed = SPEED_2500; |
| DEBUGOUT("2500 Mbs, "); |
| } else { |
| *speed = SPEED_1000; |
| DEBUGOUT("1000 Mbs, "); |
| } |
| } else if (status & IGC_STATUS_SPEED_100) { |
| *speed = SPEED_100; |
| DEBUGOUT("100 Mbs, "); |
| } else { |
| *speed = SPEED_10; |
| DEBUGOUT("10 Mbs, "); |
| } |
| |
| if (status & IGC_STATUS_FD) { |
| *duplex = FULL_DUPLEX; |
| DEBUGOUT("Full Duplex\n"); |
| } else { |
| *duplex = HALF_DUPLEX; |
| DEBUGOUT("Half Duplex\n"); |
| } |
| |
| return IGC_SUCCESS; |
| } |
| |
| /** |
| * igc_get_hw_semaphore_generic - Acquire hardware semaphore |
| * @hw: pointer to the HW structure |
| * |
| * Acquire the HW semaphore to access the PHY or NVM |
| **/ |
| s32 igc_get_hw_semaphore_generic(struct igc_hw *hw) |
| { |
| u32 swsm; |
| s32 timeout = hw->nvm.word_size + 1; |
| s32 i = 0; |
| |
| DEBUGFUNC("igc_get_hw_semaphore_generic"); |
| |
| /* Get the SW semaphore */ |
| while (i < timeout) { |
| swsm = IGC_READ_REG(hw, IGC_SWSM); |
| if (!(swsm & IGC_SWSM_SMBI)) |
| break; |
| |
| usec_delay(50); |
| i++; |
| } |
| |
| if (i == timeout) { |
| DEBUGOUT("Driver can't access device - SMBI bit is set.\n"); |
| return -IGC_ERR_NVM; |
| } |
| |
| /* Get the FW semaphore. */ |
| for (i = 0; i < timeout; i++) { |
| swsm = IGC_READ_REG(hw, IGC_SWSM); |
| IGC_WRITE_REG(hw, IGC_SWSM, swsm | IGC_SWSM_SWESMBI); |
| |
| /* Semaphore acquired if bit latched */ |
| if (IGC_READ_REG(hw, IGC_SWSM) & IGC_SWSM_SWESMBI) |
| break; |
| |
| usec_delay(50); |
| } |
| |
| if (i == timeout) { |
| /* Release semaphores */ |
| igc_put_hw_semaphore_generic(hw); |
| DEBUGOUT("Driver can't access the NVM\n"); |
| return -IGC_ERR_NVM; |
| } |
| |
| return IGC_SUCCESS; |
| } |
| |
| /** |
| * igc_put_hw_semaphore_generic - Release hardware semaphore |
| * @hw: pointer to the HW structure |
| * |
| * Release hardware semaphore used to access the PHY or NVM |
| **/ |
| void igc_put_hw_semaphore_generic(struct igc_hw *hw) |
| { |
| u32 swsm; |
| |
| DEBUGFUNC("igc_put_hw_semaphore_generic"); |
| |
| swsm = IGC_READ_REG(hw, IGC_SWSM); |
| |
| swsm &= ~(IGC_SWSM_SMBI | IGC_SWSM_SWESMBI); |
| |
| IGC_WRITE_REG(hw, IGC_SWSM, swsm); |
| } |
| |
| /** |
| * igc_get_auto_rd_done_generic - Check for auto read completion |
| * @hw: pointer to the HW structure |
| * |
| * Check EEPROM for Auto Read done bit. |
| **/ |
| s32 igc_get_auto_rd_done_generic(struct igc_hw *hw) |
| { |
| s32 i = 0; |
| |
| DEBUGFUNC("igc_get_auto_rd_done_generic"); |
| |
| while (i < AUTO_READ_DONE_TIMEOUT) { |
| if (IGC_READ_REG(hw, IGC_EECD) & IGC_EECD_AUTO_RD) |
| break; |
| msec_delay(1); |
| i++; |
| } |
| |
| if (i == AUTO_READ_DONE_TIMEOUT) { |
| DEBUGOUT("Auto read by HW from NVM has not completed.\n"); |
| return -IGC_ERR_RESET; |
| } |
| |
| return IGC_SUCCESS; |
| } |
| |
| /** |
| * igc_disable_pcie_master_generic - Disables PCI-express master access |
| * @hw: pointer to the HW structure |
| * |
| * Returns IGC_SUCCESS if successful, else returns -10 |
| * (-IGC_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not caused |
| * the master requests to be disabled. |
| * |
| * Disables PCI-Express master access and verifies there are no pending |
| * requests. |
| **/ |
| s32 igc_disable_pcie_master_generic(struct igc_hw *hw) |
| { |
| u32 ctrl; |
| s32 timeout = MASTER_DISABLE_TIMEOUT; |
| |
| DEBUGFUNC("igc_disable_pcie_master_generic"); |
| |
| ctrl = IGC_READ_REG(hw, IGC_CTRL); |
| ctrl |= IGC_CTRL_GIO_MASTER_DISABLE; |
| IGC_WRITE_REG(hw, IGC_CTRL, ctrl); |
| |
| while (timeout) { |
| if (!(IGC_READ_REG(hw, IGC_STATUS) & |
| IGC_STATUS_GIO_MASTER_ENABLE)) |
| break; |
| usec_delay(100); |
| timeout--; |
| } |
| |
| if (!timeout) { |
| DEBUGOUT("Master requests are pending.\n"); |
| return -IGC_ERR_MASTER_REQUESTS_PENDING; |
| } |
| |
| return IGC_SUCCESS; |
| } |
| // clang-format on |