blob: a93dfe071a4ae2aa6f96b766a9a8d89d1533494c [file] [log] [blame]
// Copyright 2019 The Fuchsia Authors. All rights reserved.
// Use of this source code is governed by a BSD-style license that can be found
// in the LICENSE file.
library fuchsia.hardware.wlan.mac;
using ddk.hw.wlan.wlaninfo;
using fuchsia.hardware.ethernet;
using fuchsia.hardware.wlan.info;
using zx;
struct WlanmacInfo {
/// MAC address.
array<uint8>:6 mac_addr;
/// MAC role
ddk.hw.wlan.wlaninfo.WlanInfoMacRole mac_role;
/// Bitmask indicating WlanInfoPhyType values supported by the hardware.
ddk.hw.wlan.wlaninfo.WlanInfoPhyType supported_phys;
/// Bitmask indicating enabled WlanInfoDriverFeature values.
ddk.hw.wlan.wlaninfo.WlanInfoDriverFeature driver_features;
/// Bitmask indicating enabled WlanInfoHardwareCapability values.
ddk.hw.wlan.wlaninfo.WlanInfoHardwareCapability caps;
/// Supported bands.
array<ddk.hw.wlan.wlaninfo.WlanInfoBandInfo>:WLAN_INFO_MAX_BANDS bands;
uint32 bands_count;
};
enum WlanRxInfoFlags : uint32 {
/// The FCS for the received frame was invalid.
FCS_INVALID = 0x1;
/// Padding was added after the MAC header to align the frame body to 4 bytes.
FRAME_BODY_PADDING_4 = 0x2;
// Bits 2-31 reserved
};
const int8 WLAN_RSSI_DBM_MIN = -97;
const int8 WLAN_RSSI_DBM_MAX = -10;
const int8 WLAN_RSSI_DBM_INVALID = 0;
const int16 WLAN_SNR_DBH_MIN = 1;
const int16 WLAN_SNR_DBH_MAX = 120; // 60 * 2
const int16 WLAN_SNR_DBH_INVALID = 0;
struct WlanRxInfo {
/// Receive flags. These represent boolean flags as opposed to enums or value-based info which
/// are represented below. Values should be taken from the WLAN_RX_INFO_FLAGS_* enum.
uint32 rx_flags;
/// Bitmask indicating which of the following fields are valid in this struct. Reserved flags
/// must be zero.
uint32 valid_fields;
/// The PHY format of the device at the time of the operation.
uint16 phy;
/// The data rate of the device, measured in units of 0.5 Mb/s.
uint32 data_rate;
/// The channel of the device at the time of the operation. This field must be included.
fuchsia.hardware.wlan.info.WlanChannel chan;
/// The modulation and coding scheme index of the device at the time of the operation. Depends
/// on the PHY format and channel width.
uint8 mcs;
/// Received Signal Strength Indicator.
int8 rssi_dbm;
/// Signal-to-Noise Ratio, in 0.5 dB.
int16 snr_dbh;
};
enum WlanTxInfoFlags : uint8 {
PROTECTED = 0x1;
/// For rate control: indicate an important data frame, such as EAPOL, which should be sent
/// _reliably_ rather than fast, and is exempt from rate probing
FAVOR_RELIABILITY = 0x2;
/// Indicate that this packet should be sent out with QoS header when possible (11n+).
// TODO(fxbug.dev/29622): remove this when MLME supports QoS tag.
QOS = 0x4;
};
enum WlanTxInfoValid : uint8 {
DATA_RATE = 0x1;
TX_VECTOR_IDX = 0x2;
PHY = 0x4;
CHAN_WIDTH = 0x4;
MCS = 0x8;
// Bits 5-31 reserved
};
struct WlanTxInfo {
/// Transmit flags. These represent boolean options as opposed to enums or other value-based
/// info which are represented below. Values should be taken from the WLAN_TX_INFO_FLAGS_* enum.
uint32 tx_flags;
/// Bitmask indicating which of the following fields are valid in this struct. Reserved flags
/// must be zero. Values for fields not indicated by a flag may be chosen at the discretion of
/// the wlanmac driver.
uint32 valid_fields;
// Will be sent back in wlan_tx_status_t if Minstrel is enabled for the device, indicated by
// WLAN_TX_INFO_VALID_TX_VECTOR_IDX.
uint16 tx_vector_idx;
// The PHY format to be used to transmit this packet.
uint16 phy;
// The channel width to be used to transmit this packet.
fuchsia.hardware.wlan.info.WlanChannelBandwidth cbw;
/// The modulation and coding scheme index for this packet. Depends on the PHY format and
/// channel width.
uint8 mcs;
};
const uint16 WLAN_TX_VECTOR_IDX_INVALID = 0;
const uint32 WLAN_TX_STATUS_MAX_ENTRY = 8;
struct WlanTxStatusEntry {
uint16 tx_vector_idx;
/// Number of total attempts with this specific tx vector, including successful attempts.
/// DDK assumes the number of attempts per packet will not exceed 255. (usually <= 8)
uint8 attempts;
};
struct WlanTxStatus {
/// up to 8 different tx_vector for one PPDU frame.
/// WLAN_TX_VECTOR_IDX_INVALID indicates no more entries.
array<WlanTxStatusEntry>:WLAN_TX_STATUS_MAX_ENTRY tx_status_entry;
/// Destination mac address, or addr1 in packet header.
array<uint8>:6 peer_addr;
/// Outcome of packet transmission. True iff ACK was received from peer.
bool success;
};
enum WlanProtection : uint8 {
NONE = 0;
RX = 1;
TX = 2;
RX_TX = 3;
};
struct WlanKeyConfig {
/// The BSSID for which this key is relevant.
uint8 bssid;
/// Which path to protect: None, TX, RX, or TX and RX.
WlanProtection protection;
/// IEEE Cipher suite selector.
/// See IEEE Std 802.11-2016, 9.4.2.25.2, Table 9-131
array<uint8>:3 cipher_oui;
uint8 cipher_type;
/// Whether this key is a pairwise, group or peer key.
fuchsia.hardware.wlan.info.WlanKeyType key_type;
/// The peer MAC address for pairwise and peer keys.
/// For group keys this value is always the broadcast address.
array<uint8>:6 peer_addr;
/// Index for rotating keys, e.g. group keys.
/// This value is always 0 for key types which aren't rotating, e.g. pairwise keys.
uint8 key_idx;
// Length of the supplied key.
uint8 key_len;
// They key's actual bytes.
array<uint8>:32 key;
/// Receive Sequence Counter for group keys only.
/// In all other cases the RSC will be 0.
uint64 rsc;
};
struct WlanTxPacket {
/// Leading bytes of the packet to transmit. Any 802.11 frame headers must be in the packet_head.
fuchsia.hardware.ethernet.EthernetNetbuf packet_head;
/// Trailing bytes of the packet to transmit. May be NULL if all bytes to be transmitted are in
/// the packet_head. Typically used to transport ethernet frames from a higher layer.
[Mutable] vector<fuchsia.hardware.ethernet.EthernetNetbuf> packet_tail;
/// If packet_tail is not NULL, the offset into the packet tail that should be used before
/// transmitting. The ethernet_netbuf_t len field will reflect the original packet length without
/// the offset.
uint16 tail_offset;
/// Additional data needed to transmit the packet.
WlanTxInfo info;
};
enum WlanIndication : uint8 {
PRE_TBTT = 1;
BCN_TX_COMPLETE = 2;
HW_SCAN_COMPLETE = 3;
HW_SCAN_ABORTED = 4;
};
enum WlanHwScanType : uint8 {
ACTIVE = 1;
PASSIVE = 2;
};
struct WlanHwScanConfig {
WlanHwScanType scan_type;
/// Number of channels in the |channels| array. Must be at least 1
uint8 num_channels;
/// Channel numbers to scan
array<uint8>:WLAN_INFO_CHANNEL_LIST_MAX_CHANNELS channels;
/// SSID for directed probe requests
fuchsia.hardware.wlan.info.WlanSsid ssid;
};
enum WlanHwScan : uint8 {
SUCCESS = 0;
ABORTED = 1;
};
struct WlanHwScanResult {
WlanHwScan code;
};
/// Includes the information about beacon template.
struct WlanBcnConfig {
/// Points to the beacon template. Since this is just the template, some packet content can
/// contain only minimum valid info. They will be changed later by hardware/firmware or software.
/// Note that the driver must copy the packet content into its own memory and cannot rely on
/// the pointers in the struct.
WlanTxPacket tmpl;
/// TIM offset (in bytes) to the start of |bcn_tmpl|. This points to the first byte of TIM IE,
/// which is the tag ID.
uint64 tim_ele_offset;
/// in TU
uint16 beacon_interval;
};
[BanjoLayout = "ddk-interface"]
protocol WlanmacIfc {
/// Report the status of the wlanmac device.
Status(uint32 status) -> ();
/// Submit received data to the next driver. info must not be NULL.
Recv(uint32 flags, [Buffer] vector<uint8> data, WlanRxInfo info);
/// complete_tx() is called to return ownership of a packet to the wlan driver.
/// Return status indicates queue state:
/// ZX_OK: Packet has been enqueued.
/// Other: Packet could not be enqueued.
///
/// Upon a return of ZX_OK, the packet has been enqueued, but no information is returned as to
/// the completion state of the transmission itself.
CompleteTx([InOut] WlanTxPacket packet, zx.status status) -> ();
/// Reports an indication of a status, state or action to the wlan driver.
Indication(uint32 ind);
/// Reports the status of an attempted transmission.
/// |tx_status|: contains status info of one transmitted packet to one peer at one specific rate.
ReportTxStatus(WlanTxStatus tx_status);
/// Reports completion of a hardware scan
HwScanComplete(WlanHwScanResult result);
};
[BanjoLayout = "ddk-protocol"]
protocol Wlanmac {
/// Obtain information about the device and supported features
/// Safe to call at any time.
Query(uint32 options) -> (zx.status status, WlanmacInfo info);
/// Start wlanmac running with ifc_virt
/// Callbacks on ifc may be invoked from now until stop() is called
Start(WlanmacIfc ifc) -> (zx.status status, zx.handle:CHANNEL sme_channel);
/// Shut down a running wlanmac
/// Safe to call if the wlanmac is already stopped.
Stop() -> ();
/// Queue the data for transmit. Return status indicates queue state:
/// ZX_ERR_SHOULD_WAIT: Packet is being enqueued.
/// ZX_OK: Packet has been enqueued.
/// Other: Packet could not be enqueued.
///
/// In the SHOULD_WAIT case the driver takes ownership of the wlan_tx_packet_t and must call
/// complete_tx() to return it once the enqueue is complete. complete_tx() may be used to return
/// the packet before transmission itself completes, and MUST NOT be called from within the
/// queue_tx() implementation.
///
/// queue_tx() may be called at any time after start() is called including from multiple threads
/// simultaneously.
QueueTx(uint32 options, [InOut] WlanTxPacket pkt) -> (zx.status status);
// Set the radio channel
SetChannel(uint32 options, fuchsia.hardware.wlan.info.WlanChannel chan) -> (zx.status status);
// Configures a BSS which the STA is either joining or managing.
ConfigureBss(uint32 options, fuchsia.hardware.wlan.info.WlanBssConfig config) -> (zx.status st);
// Enables or disables hardware Beaconing.
// * |bcn_cfg|: Pass `nullptr` to disable hardware Beacons. Used by hardware beacon offload.
EnableBeaconing(uint32 options, WlanBcnConfig bcn_cfg) -> (zx.status st);
/// Configures a Beacon frame in hardware to announce the BSS' existence.
/// * pkt: Pass `nullptr` to disable hardware Beacons. Used by software generated beacon.
/// TODO(fxbug.dev/29298): Rename to update_beacon.
ConfigureBeacon(uint32 options, WlanTxPacket pkt) -> (zx.status st);
/// Specify a key for frame protection.
SetKey(uint32 options, WlanKeyConfig key_config) -> (zx.status st);
/// Notifies MAC and PHY parameters negotiated through a successful association
ConfigureAssoc(uint32 options, fuchsia.hardware.wlan.info.WlanAssocCtx assoc_ctx) -> (zx.status st);
/// Notifies MAC and PHY that the peer has been de-associated.
ClearAssoc(uint32 options, vector<uint8> peer_addr) -> (zx.status st);
/// Initiate a hardware scan
///
/// Once the scan starts, scan results will be delivered as beacon and probe response frames
/// via the regular rx path.
///
/// Unless an error is returned immediately, the driver will eventually
/// call wlanmac_ifc->hw_scan_complete()
StartHwScan(WlanHwScanConfig scan_config) -> (zx.status st);
/// Notifies change of WMM parameters for specified AC
UpdateWmmParams(
fuchsia.hardware.wlan.info.WlanAc ac,
fuchsia.hardware.wlan.info.WlanWmmParams params
) -> (zx.status st);
};