sdk/fidl/fuchsia.bluetooth.le/peer.fidl

// Copyright 2019 The Fuchsia Authors. All rights reserved.
// Use of this source code is governed by a BSD-style license that can be
// found in the LICENSE file.
library fuchsia.bluetooth.le;

using fuchsia.bluetooth as bt;
using fuchsia.bluetooth.gatt2 as gatt2;
using zx;

/// Information obtained from advertising and scan response data broadcast by a peer.
type ScanData = table {
    /// The radio transmit power level reported by an advertising and/or scannable peer.
    ///
    /// NOTE: This field should NOT be confused with the "connection TX Power Level" of a peer that
    /// is currently connected to the system obtained via the "Transmit Power reporting" feature.
    1: tx_power int8;

    /// The appearance of the device.
    2: appearance bt.Appearance;

    /// Service UUIDs.
    3: service_uuids vector<bt.Uuid>:MAX;

    /// Service data entries.
    4: service_data vector<ServiceData>:MAX;

    /// Manufacturer-specific data entries.
    5: manufacturer_data vector<ManufacturerData>:MAX;

    /// String representing a URI to be advertised, as defined in [IETF STD 66](https://tools.ietf.org/html/std66).
    /// Each entry should be a UTF-8 string including the scheme. For more information, see
    /// https://www.iana.org/assignments/uri-schemes/uri-schemes.xhtml for allowed schemes;
    /// NOTE: Bluetooth advertising compresses schemas over the air to save space. See
    /// https://www.bluetooth.com/specifications/assigned-numbers/uri-scheme-name-string-mapping.
    6: uris vector<string:MAX_URI_LENGTH>:MAX;

    /// The monotonic time when this scan data was received.
    7: timestamp zx.Time;
};

/// Represents a Bluetooth Low Energy peer that may act in the broadcaster, peripheral, or central
/// role. The peer's role depends on whether it is obtained from the Central or Peripheral protocol.
type Peer = table {
    /// Uniquely identifies this peer on the current system.
    ///
    /// This field is always present.
    1: id bt.PeerId;

    /// Whether or not this peer is connectable. Non-connectable peers are typically in the LE
    /// broadcaster role.
    ///
    /// This field is always present.
    2: connectable bool;

    /// The last observed signal strength of this peer. This field is only present for a peer that
    /// is broadcasting. The RSSI can be stale if the peer has not been advertising.
    ///
    /// NOTE: This field should NOT be confused with the "connection RSSI" of a peer that is currently
    /// connected to the system.
    3: rssi int8;

    @deprecated("Use `data` instead")
    4: advertising_data AdvertisingData;

    /// The name of this peer. The name is often obtained during a scan procedure and can get
    /// updated during the name discovery procedure following a connection.
    ///
    /// This field is present if the name is known.
    5: name bt.DeviceName;

    /// Information from advertising and scan response data broadcast by this peer. When present,
    /// this contains the advertising data last received from the peer.
    6: data ScanData;

    /// Whether or not this peer is bonded.
    ///
    /// This field is always present.
    7: bonded bool;

    /// The value of the system monotonic clock, measured at the time this peer
    /// was last updated (e.g. due to reception of an advertisement).
    ///
    /// This field is always present.
    8: last_updated zx.Time;
};

/// Protocol that represents the connection to a peer. This can be used to interact with GATT
/// services and establish L2CAP channels.
///
/// This lifetime of this capability is tied to that of the LE connection it represents. Closing the
/// channel results in a disconnection if no other clients hold a Connection to the same peer.
closed protocol Connection {
    // Bind the server end of a `fuchsia.bluetooth.gatt2/Client` corresponding to the connected
    // peer.
    /// The following epitaphs may be sent by the server on error:
    /// + `ZX_ERR_ALREADY_BOUND`: A Client server has already been bound in this Connection
    ///                           protocol. The existing Client should be used.
    @transitional
    @available(added=HEAD)
    strict RequestGattClient(resource struct {
        client server_end:gatt2.Client;
    });
};