| class OpCodes: | |
| """USB Control Transfer operation codes""" | |
| setMainFineResistorOffset=0x02 #LVPM Calibration value, 8-bits signed, ohms = 0.05 + 0.0001*offset | |
| setMainCoarseResistorOffset=0x11 #LVPM Calibration value, 8-bits signed, ohms = 0.05 + 0.0001*offset | |
| setUsbFineResistorOffset=0x0D #LVPM Calibration value, 8-bits signed, ohms = 0.05 + 0.0001*offset | |
| setUsbCoarseResistorOffset=0x12 #LVPM Calibration value, 8-bits signed, ohms = 0.05 + 0.0001*offset | |
| setAuxFineResistorOffset=0x0E #LVPM Calibration value, 8-bits signed, ohms = 0.1 + 0.0001*offset | |
| setAuxCoarseResistorOffset=0x13 #LVPM Calibration value, 8-bits signed, ohms = 0.1 + 0.0001*offset | |
| calibrateMainVoltage=0x03 #Internal voltage calibration, affects accuracy of setHVMainVoltage | |
| resetPowerMonitor=0x05 #Reset the PIC. Causes disconnect. | |
| setPowerupTime=0x0C #time in milliseconds that the powerup current limit is in effect. | |
| setTemperatureLimit=0x29 #Temperature limit in Signed Q7.8 format | |
| setUsbPassthroughMode=0x10 #Sets USB Passthrough mode according to value. Off = 0, On = 1, Auto = 2 | |
| setMainFineScale = 0x1A #HVPM Calibration value, 32-bits, unsigned | |
| setMainCoarseScale = 0x1B #HVPM Calibration value, 32-bits, unsigned | |
| setUSBFineScale = 0x1C #HVPM Calibration value, 32-bits, unsigned | |
| setUSBCoarseScale = 0x1D #HVPM Calibration value, 32-bits, unsigned | |
| setAuxFineScale = 0x1E #HVPM Calibration value, 32-bits, unsigned | |
| setAuxCoarseScale = 0x1F #HVPM Calibration value, 32-bits, unsigned | |
| setVoltageChannel = 0x23 #Sets voltage channel: Value 00 = Main & USB voltage measurements. Value 01 = Main & Aux voltage measurements | |
| SetPowerUpCurrentLimit = 0x43 #Sets power-up current limit. HV Amps = 15.625*(1.0-powerupCurrentLimit/65535) #LV amps = 8.0*(1.0-powerupCurrentLimit/1023.0) | |
| SetRunCurrentLimit = 0x44 #Sets runtime current limit HV Amps = 15.625*(1.0-powerupCurrentLimit/65535) #LV amps = 8.0*(1.0-powerupCurrentLimit/1023.0) | |
| setMainVoltage = 0x41 # Voltage = value * 1048576 | |
| getSerialNumber = 0x42 | |
| SetMainFineZeroOffset=0x25 #Zero-level offset | |
| SetMainCoarseZeroOffset = 0x26 #Zero-level offset | |
| SetUSBFineZeroOffset = 0x27 #Zero-level offset | |
| SetUSBCoarseZeroOffset = 0x28 #Zero-level offset | |
| FirmwareVersion = 0xC0 #Read-only, gets the firmware version | |
| ProtocolVersion = 0xC1 #Read-only, gets the Protocol version | |
| HardwareModel = 0x45 #0 = unknown, 1 = LV, 2 = HV | |
| getStartStatus = 0xC4 | |
| dacCalLow = 0x88 #2.5V ADC Reference Calibration | |
| dacCalHigh = 0x89 #4.096V ADC Reference Calibration | |
| Stop = 0xFF | |
| class ReturnCodes: | |
| """Status return codes""" | |
| #TODO: Should really consolidate this with a few other misc values. | |
| ERROR = 0xfffffffE | |
| CURRENT_FIRMWARE_REV = 32 | |
| class HardwareModel: | |
| """Hardware Model Types""" | |
| UNKNOWN = 0 | |
| LVPM = 1 | |
| HVPM = 2 | |
| class Control_Codes: | |
| """USB Protocol codes.""" | |
| USB_IN_PACKET = 0xC0 | |
| USB_OUT_PACKET = 0x40 | |
| USB_REQUEST_START = 0x02 | |
| USB_REQUEST_STOP = 0x03 | |
| USB_SET_VALUE = 0x01 | |
| USB_REQUEST_RESET_TO_BOOTLOADER = 0xFF | |
| class Conversion: | |
| """Values used for converting from desktop to the PIC""" | |
| FLOAT_TO_INT = 1048576 | |
| class USB_Passthrough: | |
| """Values for setting or retrieving the USB Passthrough mode.""" | |
| Off = 0 | |
| On = 1 | |
| Auto = 2 | |
| class VoltageChannel: | |
| """Values for setting or retrieving the Voltage Channel.""" | |
| Main = 0 | |
| USB = 1 | |
| Aux = 2 | |
| class statusPacket: | |
| """Values stored in the Power Monitor EEPROM. Each corresponds to an opcode""" | |
| firmwareVersion = 0 #Firmware version number. | |
| protocolVersion = 0 #Protocol version number. | |
| temperature = 0 #Current temperature reading from the board. | |
| serialNumber = 0 #Unit's serial number. | |
| powerupCurrentLimit = 0 #Max current during startup before overcurrent protection circuit activates. LVPM is 0-8A, HVPM is 0-15A. | |
| runtimeCurrentLimit = 0 #Max current during runtime before overcurrent protection circuit activates. LVPM is 0-8A, HVPM is 0-15A. | |
| powerupTime = 0 #Time in ms the powerupcurrent limit will be used. | |
| temperatureLimit = 0 #Temperature limit in Signed Q7.8 format | |
| usbPassthroughMode = 0 # Off = 0, On = 1, Auto = 2 | |
| mainFineScale = 0 #HVPM Calibration value, 32-bits, unsigned | |
| mainCoarseScale = 0#HVPM Calibration value, 32-bits, unsigned | |
| usbFineScale = 0#HVPM Calibration value, 32-bits, unsigned | |
| usbCoarseScale = 0#HVPM Calibration value, 32-bits, unsigned | |
| auxFineScale = 0#HVPM Calibration value, 32-bits, unsigned | |
| auxCoarseScale = 0#HVPM Calibration value, 32-bits, unsigned | |
| mainFineZeroOffset = 0 #HVPM-only, Zero-level offset | |
| mainCoarseZeroOffset = 0 #HVPM-only, Zero-level offset | |
| usbFineZeroOffset = 0 #HVPM-only, Zero-level offset | |
| usbCoarseZeroOffset = 0 #HVPM-only, Zero-level offset | |
| hardwareModel = 0 #HVPM-only, Zero-level offset | |
| mainFineResistorOffset = 0 #signed, ohms = 0.05 + 0.0001*offset | |
| mainCoarseResistorOffset = 0 #signed, ohms = 0.05 + 0.0001*offset | |
| usbFineResistorOffset = 0 #signed, ohms = 0.05 + 0.0001*offset | |
| usbCoarseResistorOffset = 0 #signed, ohms = 0.05 + 0.0001*offset | |
| auxFineResistorOffset = 0 #signed, ohms = 0.10 + 0.0001*offset | |
| auxCoarseResistorOffset = 0 #signed, ohms = 0.10 + 0.0001*offset | |
| dacCalLow = 0 | |
| dacCalHigh = 0 | |
| class BootloaderCommands: | |
| """Bootloader opcodes. Used when reflashing the Power Monitor""" | |
| ReadVersion = 0x00 | |
| ReadFlash = 0x01 | |
| WriteFlash = 0x02 | |
| EraseFlash = 0x03 | |
| ReadEEPROM = 0x04 | |
| WriteEEPROM = 0x05 | |
| ReadConfig = 0x06 | |
| WriteConfig = 0x07 | |
| Reset = 0xFF | |
| class BootloaderMemoryRegions: | |
| """Memory regions of the PIC18F4550""" | |
| Flash = 0x00 | |
| IDLocs = 0x20 | |
| Config = 0x30 | |
| EEPROM = 0xf0 | |
| class hexLineType: | |
| """line types used in the intel hex format. Used when reflashing the Power Monitor.""" | |
| Data = 0 | |
| EndOfFile = 1 | |
| ExtendedSegmentAddress = 2 | |
| StartSegmentAddress = 3 | |
| ExtendedLinearAddress = 4 | |
| StartLinearAddress = 5 | |
| class SampleType(object): | |
| """Corresponds to the sampletype field from a sample packet.""" | |
| Measurement = 0x00 | |
| ZeroCal = 0x10 | |
| invalid = 0x20 | |
| refCal = 0x30 | |