sdk/fidl/fuchsia.wlan.mlme/wlan_mlme.fidl

// Copyright 2017 The Fuchsia Authors. All rights reserved.
// Use of this source code is governed by a BSD-style license that can be
// found in the LICENSE file.

library fuchsia.wlan.mlme;

using fuchsia.wlan.common;
using fuchsia.wlan.mesh;

// Stub types for communicating between the wlan service and the MLME drivers. Based on the 802.11
// MLME SAP interface (IEEE Std 802.11-2016 section 6.3).

// TODO(NET-631): restore the commented out enum aliases

// MLME-SCAN.request (IEEE Std 802.11-2016 6.3.3.2)

enum BSSTypes {
    INFRASTRUCTURE = 1;
    PERSONAL = 2;
    INDEPENDENT = 3;
    MESH = 4;
    ANY_BSS = 5;
    //LAST = ANY_BSS;
};

enum ScanTypes {
    ACTIVE = 1;
    PASSIVE = 2;
    //LAST = PASSIVE;
};

struct ScanRequest {
    uint64 txn_id;
    BSSTypes bss_type;
    array<uint8>:6 bssid;
    bytes:32 ssid;
    ScanTypes scan_type;
    uint32 probe_delay; // in TimeUnits
    vector<uint8>? channel_list;
    uint32 min_channel_time; // in TimeUnits
    uint32 max_channel_time; // in TimeUnits
    // RequestInformation
    vector<bytes:32>? ssid_list;
    // ChannelUsage
    // AccessNetworkType
    // HESSID
    // Mesh ID
    // DiscoveryMode
    // VendorSpecificInfo
};

// MLME-SCAN.confirm (IEEE Std 802.11-2016 6.3.3.3)

// IEEE Std 802.11-2016, 9.4.1.4
struct CapabilityInfo {
    bool ess;
    bool ibss;
    bool cf_pollable;
    bool cf_poll_req;
    bool privacy;
    bool short_preamble;
    bool spectrum_mgmt;
    bool qos;
    bool short_slot_time;
    bool apsd;
    bool radio_msmt;
    bool delayed_block_ack;
    bool immediate_block_ack;
};

// IEEE Std 802.11-2016, 9.4.2.56

enum ChanWidthSet : uint8 {
    TWENTY_ONLY = 0;
    TWENTY_FORTY = 1;
};

enum SmPowerSave : uint8 {
    STATIC = 0;
    DYNAMIC = 1;
    RESERVED = 2;
    DISABLED = 3;
};

enum MaxAmsduLen : uint8 {
    OCTETS_3839 = 0;
    OCTETS_7935 = 1;
};

struct HtCapabilityInfo {
    bool ldpc_coding_cap;
    uint8 chan_width_set; // see enum ChanWidthSet
    uint8 sm_power_save; // see enum SmPowerSave
    bool greenfield;
    bool short_gi_20;
    bool short_gi_40;
    bool tx_stbc;
    uint8 rx_stbc;
    bool delayed_block_ack;
    uint8 max_amsdu_len; // see enum MaxAmsduLen
    bool dsss_in_40;
    bool intolerant_40;
    bool lsig_txop_protect;
};

enum MinMpduStartSpacing : uint8 {
    NO_RESTRICT = 0;
    QUARTER_USEC = 1;
    HALF_USEC = 2;
    ONE_USEC = 3;
    TWO_USEC = 4;
    FOUR_USEC = 5;
    EIGHT_USEC = 6;
    SIXTEEN_USEC = 7;
};

struct AmpduParams {
    uint8 exponent;
    uint8 min_start_spacing; // see enum MinMpduStartSpacing
};

// SupportedMcsSet
// IEEE Std 802.11-2016, 9.4.2.56.4 Table 9-164
struct SupportedMcsSet {
    // Names are deviated from //garnet/lib/wlan/common/include/wlan/common/element.h's class SupportedMcsSet
    uint64 rx_mcs_set; // bitmask indicating MCS 0-63 support
    // MCS 64-76 not supported
    uint16 rx_highest_rate; // Mbps
    bool tx_mcs_set_defined;
    bool tx_rx_diff;
    uint8 tx_max_ss; // Actual count, different from IEEE spec
    bool tx_ueqm; // Transmit Unequal Modulation
};

// HtExtCapabilities
// IEEE Std 802.11-2016, 9.4.2.56.5 Table 9-165
enum PcoTransitionTime : uint8 {
    PCO_RESERVED = 0; // Often translated as "No transition".
    PCO_400_USEC = 1;
    PCO_1500_USEC = 2;
    PCO_5000_USEC = 3;
};

enum McsFeedback : uint8 {
    MCS_NOFEEDBACK = 0;
    MCS_RESERVED = 1;
    MCS_UNSOLICIED = 2;
    MCS_BOTH = 3;
};

struct HtExtCapabilities {
    bool pco;
    uint8 pco_transition; // see enum PcoTransitionTime
    uint8 mcs_feedback; // see enum McsFeedback
    bool htc_ht_support;
    bool rd_responder;
};

// TxBfCapability
// IEEE Std 802.11-2016, 9.4.2.56.6 Table 9-166
enum Calibration : uint8 {
    CALIBRATION_NONE = 0;
    CALIBRATION_RESPOND_NOINITIATE = 1;
    CALIBRATION_RESERVED = 2;
    CALIBRATION_RESPOND_INITIATE = 3;
};

enum Feedback : uint8 {
    // Shared for csi_feedback, noncomp_feedback, comp_feedback
    FEEDBACK_NONE = 0;
    FEEDBACK_DELAYED = 1;
    FEEDBACK_IMMEDIATE = 2;
    FEEDBACK_DELAYED_IMMEDIATE = 3;
};

enum MinGroup : uint8 {
    MIN_GROUP_ONE = 0; // Meaning no grouping
    MIN_GROUP_ONE_TWO = 1;
    MIN_GROUP_ONE_FOUR = 2;
    MIN_GROUP_ONE_TWO_FOUR = 3;
};

struct TxBfCapability {
    bool implicit_rx;
    bool rx_stag_sounding;
    bool tx_stag_sounding;
    bool rx_ndp;
    bool tx_ndp;
    bool implicit;
    uint8 calibration; // see enum Calibration
    bool csi; // Explicit CsI Transmit Beamforming
    bool noncomp_steering; // Explicit Noncompressed Steering
    bool comp_steering; // Explicit Compressed Steering
    uint8 csi_feedback; // see enum Feedback
    uint8 noncomp_feedback; // see enum Feedback
    uint8 comp_feedback; // see enum Feedback
    uint8 min_grouping; // see enum MinGroup
    uint8 csi_antennas; // Actual count, different from IEEE spec
    uint8 noncomp_steering_ants; // Actual count, different from IEEE spec
    uint8 comp_steering_ants; // Actual count, different from IEEE spec
    uint8 csi_rows; // Actual count, different from IEEE spec
    uint8 chan_estimation; // Actual count, different from IEEE spec
};

// IEEE Std 802.11-2016, 9.4.2.56.7 Table 9-167
struct AselCapability {
    bool asel;
    bool csi_feedback_tx_asel; // Explicit CSI Feedback Based Transmit ASEL
    bool ant_idx_feedback_tx_asel;
    bool explicit_csi_feedback;
    bool antenna_idx_feedback;
    bool rx_asel;
    bool tx_sounding_ppdu;
};

struct HtCapabilities {
    // Note, a minimum granuality of adding fields selectively is
    // a group of BitField structure, as defined in element.h
    HtCapabilityInfo ht_cap_info;
    AmpduParams ampdu_params;
    SupportedMcsSet mcs_set;
    HtExtCapabilities ht_ext_cap;
    TxBfCapability txbf_cap;
    AselCapability asel_cap;
};

// HT Operation Element
// IEEE Std 802.11-2016 9.4.2.57 Table 9-168

// HTOperationInfo
enum SecChanOffset : uint8 {
    SECONDARY_NONE = 0; // No secondary channel
    SECONDARY_ABOVE = 1; // Secondary channel is above the primary channel
    RESERVED = 2;
    SECONDARY_BELOW = 3; // Secondary channel is below the primary channel
};

enum StaChanWidth : uint8 {
    TWENTY = 0; // 20 MHz
    ANY = 1; // Any in the Supported Channel Width set
};

enum HtProtect : uint8 {
    NONE = 0;
    NONMEMBER = 1;
    TWENTY_MHZ = 2;
    NON_HT_MIXED = 3;
};

struct HTOperationInfo {
    uint8 secondary_chan_offset; // see enum SecChanOffset
    uint8 sta_chan_width; // see enum StaChanWidth
    bool rifs_mode;
    uint8 ht_protect; // see enum HtProtect
    bool nongreenfield_present; // Nongreenfield HT STAs present
    bool obss_non_ht; // OBSS Non-HT STAs present
    uint8 center_freq_seg2; // VHT
    bool dual_beacon;
    bool dual_cts_protect;
    bool stbc_beacon;
    bool lsig_txop_protect;
    bool pco_active;
    bool pco_phase;
};

struct HtOperation {
    uint8 primary_chan; // Primary 20 MHz channel.
    HTOperationInfo ht_op_info;
    SupportedMcsSet basic_mcs_set;
};

enum MaxMpduLen : uint8 {
    OCTETS_3895 = 0;
    OCTETS_7991 = 1;
    OCTETS_11454 = 2;
};

enum VhtLinkAdaptation : uint8 {
    NO_FEEDBACK = 0;
    // 1 reserved
    UNSOLICITED = 2;
    BOTH = 3;
};

// IEEE Std 802.11-2016, 9.4.2.158.2
struct VhtCapabilitiesInfo {
    uint8 max_mpdu_len; // see enum MaxMpduLen
    uint8 supported_cbw_set;
    bool rx_ldpc;
    bool sgi_cbw80;
    bool sgi_cbw160;
    bool tx_stbc;
    uint8 rx_stbc; // number of spatial streams supported. [0, 4] are valid. [5, 7] are reserved.
    bool su_bfer;
    bool su_bfee;
    uint8 bfee_sts; // Maximum number of STS - 1, if su_bfee is true. Reserved otherwise.
    uint8 num_sounding;
    bool mu_bfer;
    bool mu_bfee;
    bool txop_ps;
    bool htc_vht;
    uint8 max_ampdu_exp;
    uint8 link_adapt; // see enum VhtLinkAdaptation
    bool rx_ant_pattern;
    bool tx_ant_pattern;
    uint8 ext_nss_bw;
};

enum VhtMcs : uint8 {
    SET_0_TO_7 = 0;
    SET_0_TO_8 = 1;
    SET_0_TO_9 = 2;
    SET_NONE = 3;
};

// IEEE Std 802.11-2016 9.4.2.158.3
struct VhtMcsNss {
    array<uint8>:8 rx_max_mcs; // idx 0 for ss1, .. idx 7 for ss8. See enum VhtMcs
    uint16 rx_max_data_rate; // Mbps
    uint8 max_nsts;

    array<uint8>:8 tx_max_mcs; // idx 0 for ss1, .. idx 7 for ss8. See enum VhtMcs
    uint16 tx_max_data_rate; // Mbps
    bool ext_nss_bw;
};

// IEEE Std 802.11-2016, Figure 9-562
struct BasicVhtMcsNss {
    array<uint8>:8 max_mcs; // idx 0 for ss1, .. idx 7 for ss8. See enum VhtMcs
};

// IEEE Std 802.11-2016 9.5.2.158
struct VhtCapabilities {
    VhtCapabilitiesInfo vht_cap_info;
    VhtMcsNss vht_mcs_nss;
};

// IEEE Std 802.11-2016 deprecates the use of CBW_160, CBW_80P80
enum VhtCbw : uint8 {
    CBW_20_40 = 0;
    CBW_80_160_80P80 = 1;
    CBW_160 = 2;
    CBW_80P80 = 3;
};

// IEEE Std 802.11-2016 9.5.2.159
struct VhtOperation {
    uint8 vht_cbw; // see enum VhtCbw
    uint8 center_freq_seg0; // channel number
    uint8 center_freq_seg1; // channel number
    BasicVhtMcsNss basic_mcs;
};

// IEEE Std 802.11-2016 6.3.3.3.2
struct BSSDescription {
    array<uint8>:6 bssid;

    bytes:32 ssid;

    BSSTypes bss_type;
    uint16 beacon_period; // in TU
    uint8 dtim_period;
    uint64 timestamp;
    uint64 local_time;

    CapabilityInfo cap;
    vector<uint8> basic_rate_set; // in 0.5 Mbps, valid value: 1-127. See Table 9-78 for 126, 127.
    vector<uint8> op_rate_set; // in 0.5 Mbps, valid value: 1-127. See Table 9-78 for 126, 127.
    bytes? country;

    // TODO(hahnr): This field represents an IE and should thus be named RSNE.
    bytes? rsn;

    int16 rcpi_dbmh; // 0.5 step dBm. Do not use encoding from IEEE Std 802.11-2016 9.4.2.38.
    int16 rsni_dbh; // 0.5 step dB.  Do not use encoding from IEEE Std 802.11-2016 9.4.2.41.

    HtCapabilities? ht_cap;
    HtOperation? ht_op;

    VhtCapabilities? vht_cap;
    VhtOperation? vht_op;

    // List up non-standard, Fuchsia only parameters
    fuchsia.wlan.common.WlanChan chan;
    int8 rssi_dbm; // dBm
};

enum ScanResultCodes {
    SUCCESS = 0;
    NOT_SUPPORTED = 1;
    INVALID_ARGS = 2;
    INTERNAL_ERROR = 3;
};

struct ScanResult {
    uint64 txn_id;
    BSSDescription bss;
};

struct ScanEnd {
    uint64 txn_id;
    ScanResultCodes code;
};

// MLME-JOIN.request (IEEE Std 802.11-2016, 6.3.4.2)

struct JoinRequest {
    BSSDescription selected_bss;
    uint32 join_failure_timeout;
    uint32 nav_sync_delay;
    vector<uint16> op_rate_set;

    // Combined with what MLME knows about the device capabilities,
    // following parameters determine what to be advertised to the peer
    // (in AssociationRequest). Effectively this way replaces the following
    // fields originally defined in MLME-JOIN.request
    // - Capability Information
    // - HT Capabilities
    // - VHT Capabilities
    // - Extended Capabilities
    fuchsia.wlan.common.PHY phy;
    fuchsia.wlan.common.CBW cbw;
};

// MLME-JOIN.confirm (IEEE Std 802.11-2016, 6.3.4.3)

enum JoinResultCodes {
    SUCCESS = 0;
    JOIN_FAILURE_TIMEOUT = 1;
    //LAST = JOIN_FAILURE_TIMEOUT;
};

struct JoinConfirm {
    JoinResultCodes result_code;
};

// MLME-AUTHENTICATE.request (IEEE Std 802.11-2016, 6.3.5.2)

enum AuthenticationTypes {
    OPEN_SYSTEM = 1;
    SHARED_KEY = 2;
    FAST_BSS_TRANSITION = 3;
    SAE = 4;
    //LAST = SAE;
};

struct AuthenticateRequest {
    array<uint8>:6 peer_sta_address;
    AuthenticationTypes auth_type;
    uint32 auth_failure_timeout;

    // etc
};

// MLME-AUTHENTICATE.confirm (IEEE Std 802.11-2016, 6.3.5.3)

enum AuthenticateResultCodes {
    SUCCESS = 0;
    REFUSED = 1;
    ANTI_CLOGGING_TOKEN_REQUIRED = 2;
    FINITE_CYCLIC_GROUP_NOT_SUPPORTED = 3;
    AUTHENTICATION_REJECTED = 4;
    AUTH_FAILURE_TIMEOUT = 5;
    //LAST = AUTH_FAILURE_TIMEOUT;
};

struct AuthenticateConfirm {
    array<uint8>:6 peer_sta_address;
    AuthenticationTypes auth_type;
    AuthenticateResultCodes result_code;

    // etc
};

// MLME-AUTHENTICATE.indication (IEEE Std 802.11-2016, 6.3.5.4)

struct AuthenticateIndication {
    array<uint8>:6 peer_sta_address;
    AuthenticationTypes auth_type;

    // etc
};

// MLME-AUTHENTICATE.response (IEEE Std 802.11-2016, 6.3.5.5)

struct AuthenticateResponse {
    array<uint8>:6 peer_sta_address;
    AuthenticateResultCodes result_code;

    // etc
};

// MLME-DEAUTHENTICATE.request (IEEE Std 802.11-2016, 6.3.6.2)

// IEEE Std 802.11-2016, 9.4.1.7, Table 9-45
enum ReasonCode : uint16 {
    // 0 Reserved
    UNSPECIFIED_REASON = 1;
    INVALID_AUTHENTICATION = 2;
    LEAVING_NETWORK_DEAUTH = 3;
    REASON_INACTIVITY = 4;
    NO_MORE_STAS = 5;
    INVALID_CLASS2_FRAME = 6;
    INVALID_CLASS3_FRAME = 7;
    LEAVING_NETWORK_DISASSOC = 8;
    NOT_AUTHENTICATED = 9;
    UNACCEPTABLE_POWER_CA = 10;
    UNACCEPTABLE_SUPPORTED_CHANNELS = 11;
    BSS_TRANSITION_DISASSOC = 12;
    REASON_INVALID_ELEMENT = 13;
    MIC_FAILURE = 14;
    FOURWAY_HANDSHAKE_TIMEOUT = 15;
    GK_HANDSHAKE_TIMEOUT = 16;
    HANDSHAKE_ELEMENT_MISMATCH = 17;
    REASON_INVALID_GROUP_CIPHER = 18;
    REASON_INVALID_PAIRWISE_CIPHER = 19;
    REASON_INVALID_AKMP = 20;
    UNSUPPORTED_RSNE_VERSION = 21;
    INVALID_RSNE_CAPABILITIES = 22;
    IEEE802_1_X_AUTH_FAILED = 23;
    REASON_CIPHER_OUT_OF_POLICY = 24;
    TDLS_PEER_UNREACHABLE = 25;
    TDLS_UNSPECIFIED_REASON = 26;
    SSP_REQUESTED_DISASSOC = 27;
    NO_SSP_ROAMING_AGREEMENT = 28;
    BAD_CIPHER_OR_AKM = 29;
    NOT_AUTHORIZED_THIS_LOCATION = 30;
    SERVICE_CHANGE_PRECLUDES_TS = 31;
    UNSPECIFIED_QOS_REASON = 32;
    NOT_ENOUGH_BANDWIDTH = 33;
    MISSING_ACKS = 34;
    EXCEEDED_TXOP = 35;
    STA_LEAVING = 36;
    // Values 37 and 38 are overloaded but should be clear from context.
    END_TS_BA_DLS = 37;
    UNKNOWN_TS_BA = 38;
    TIMEOUT = 39;
    // 40-44 Reserved
    PEERKEY_MISMATCH = 45;
    PEER_INITIATED = 46;
    AP_INITIATED = 47;
    REASON_INVALID_FT_ACTION_FRAME_COUNT = 48;
    REASON_INVALID_PMKID = 49;
    REASON_INVALID_MDE = 50;
    REASON_INVALID_FTE = 51;
    MESH_PEERING_CANCELED = 52;
    MESH_MAX_PEERS = 53;
    MESH_CONFIGURATION_POLICY_VIOLATION = 54;
    MESH_CLOSE_RCVD = 55;
    MESH_MAX_RETRIES = 56;
    MESH_CONFIRM_TIMEOUT = 57;
    MESH_INVALID_GTK = 58;
    MESH_INCONSISTENT_PARAMETERS = 59;
    MESH_INVALID_SECURITY_CAPABILITY = 60;
    MESH_PATH_ERROR_NO_PROXY_INFORMATION = 61;
    MESH_PATH_ERROR_NO_FORWARDING_INFORMATION = 62;
    MESH_PATH_ERROR_DESTINATION_UNREACHABLE = 63;
    MAC_ADDRESS_ALREADY_EXISTS_IN_MBSS = 64;
    MESH_CHANNEL_SWITCH_REGULATORY_REQUIREMENTS = 65;
    MESH_CHANNEL_SWITCH_UNSPECIFIED = 66;
    // 67 - 65535 Reserved
};

struct DeauthenticateRequest {
    array <uint8>:6 peer_sta_address;
    // TODO(tkilbourn): define a ReasonCode enum for FIDL
    ReasonCode reason_code;
    // VendorSpecificInfo
};

// MLME-DEAUTHENTICATE.confirm (IEEE Std 802.11-2016, 6.3.6.3)

struct DeauthenticateConfirm {
    array <uint8>:6 peer_sta_address;
};

// MLME-DEAUTHENTICATE.indication (IEEE Std 802.11-2016, 6.3.6.4)

struct DeauthenticateIndication {
    array<uint8>:6 peer_sta_address;
    // TODO(tkilbourn): define a ReasonCode enum for FIDL
    ReasonCode reason_code;
    // VendorSpecificInfo
};

// MLME-ASSOCIATE.request (IEEE Std 802.11-2016, 6.3.7.2)

struct AssociateRequest {
    array<uint8>:6 peer_sta_address;
    // TODO(hahnr): This field represents an IE and should thus be named RSNE.
    bytes? rsn;

    // etc
};

// MLME-ASSOCIATE.confrm (IEEE Std 802.11-2016, 6.3.7.3)

enum AssociateResultCodes {
    SUCCESS = 0;
    REFUSED_REASON_UNSPECIFIED = 1;
    REFUSED_NOT_AUTHENTICATED = 2;
    REFUSED_CAPABILITIES_MISMATCH = 3;
    REFUSED_EXTERNAL_REASON = 4;
    REFUSED_AP_OUT_OF_MEMORY = 5;
    REFUSED_BASIC_RATES_MISMATCH = 6;
    REJECTED_EMERGENCY_SERVICES_NOT_SUPPORTED = 7;
    REFUSED_TEMPORARILY = 8;
};

struct AssociateConfirm {
    AssociateResultCodes result_code;
    // CapabilityInformation
    uint16 association_id;

    // etc
};

// MLME-ASSOCIATE.indication (IEEE Std 802.11-2016, 6.3.7.4)

struct AssociateIndication {
    array<uint8>:6 peer_sta_address;
    // CapabilityInformation
    uint16 listen_interval;
    bytes? ssid;
    // OperationalRateSet
    // BSSMembershipSelectorSet
    bytes? rsn;

    // etc
};

// MLME-ASSOCIATE.response (IEEE Std 802.11-2016, 6.3.7.5)

struct AssociateResponse {
    array<uint8>:6 peer_sta_address;
    AssociateResultCodes result_code;
    uint16 association_id;

    // etc
};

// MLME-DISASSOCIATE.request (IEEE Std 802.11-2016, 6.3.9.1)

struct DisassociateRequest {
    array<uint8>:6 peer_sta_address;
    // TODO(tkilbourn): define a ReasonCode enum for FIDL
    uint16 reason_code;
    // VendorSpecificInfo
};

// MLME-DISASSOCIATE.confirm (IEEE Std 802.11-2016, 6.3.9.2)

struct DisassociateConfirm {
    int32 status;
};

// MLME-DISASSOCIATE.indication (IEEE Std 802.11-2016, 6.3.9.3)

struct DisassociateIndication {
    array<uint8>:6 peer_sta_address;
    // TODO(tkilbourn): define a ReasonCode enum for FIDL
    uint16 reason_code;
    // VendorSpecificInfo
};

// MLME-RESET.request (IEEE Std 802.11-2016, 6.3.10.2)

struct ResetRequest {
    array<uint8>:6 sta_address;
    bool set_default_mib;
};

// MLME-START.request (IEEE Std 802.11-2016, 6.3.11.2)

// See dot11CountryString of IEEE Std 802.11-2016, Annex C
const uint8 countryEnvironAll = 32;        // an ASCII ' ' character
const uint8 countryEnvironOutdoor = 79;    // an ASCII 'O' character
const uint8 countryEnvironIndoor = 73;     // an ASCII 'I' character
const uint8 countryEnvironNonCountry = 88; // an ASCII 'X' character

// Information derived from Country Element, IEEE Std 802.11-2016, 9.4.2.9.
struct Country {
    array<uint8>:2 alpha2; // ISO 3116-1

    // countryEnviron constant from above
    // or Operating Class Table number from IEEE Std 802.11-2016 Annex D.
    uint8 suffix;
};

struct StartRequest {
    bytes:32 ssid;
    BSSTypes bss_type;
    uint16 beacon_period; // in TU
    uint8 dtim_period;

    // PHY parameter sets
    uint8 channel;

    // TODO(porce): Conditionally present. See IEEE Std 802.11-2016, 10.2, 11.8, 11.10.
    // See also dot11MultiDomainCapabilityActivated.
    Country country;

    bytes:32 mesh_id;

    // TODO(hahnr): Add additional elements.

    // Although MLME-START.request is used to start a BSS, IEEE does not include an RSNE in this
    // primitive. However, IEEE doesn't define any other primitive to configure the RSN after its
    // BSS was started. The RSNE must be available when the BSS is started, and thus, this is the
    // right place to transfer the RSNE to the MLME.
    bytes? rsne;

    // Combined with what MLME knows about the device capabilities,
    // following parameters determine what to be advertised to the peer
    // (in Beacons/ProbeResponse/AssociationResponse). Effectively this way replaces the following
    // fields originally defined in MLME-START.request.
    // TODO(WLAN-909): Replace phy and cbw with full-fledged parameters below.
    // - Capability Information
    // - HT Capabilities
    // - HT Operation
    // - VHT Capabilities
    // - VHT Operation
    // - Extended Capabilities
    fuchsia.wlan.common.PHY phy;
    fuchsia.wlan.common.CBW cbw;
};

// MLME-START.confirm (IEEE Std 802.11-2016, 6.3.11.3)

enum StartResultCodes {
    SUCCESS = 0;
    BSS_ALREADY_STARTED_OR_JOINED = 1;
    RESET_REQUIRED_BEFORE_START = 2;
    NOT_SUPPORTED = 3;
    INTERNAL_ERROR = 4;
};

struct StartConfirm {
    StartResultCodes result_code;
};

// MLME-STOP.request (IEEE Std 802.11-2016, 6.3.12.2)

struct StopRequest {
    bytes:32 ssid;
};

enum StopResultCodes {
    SUCCESS = 0;
    BSS_ALREADY_STOPPED = 1;
    INTERNAL_ERROR = 2;
};

struct StopConfirm {
    StopResultCodes result_code;
};

// MLME-SETKEYS.request (IEEE Std 802.11-2016 6.3.19.1)

enum KeyType {
    GROUP = 1;
    PAIRWISE = 2;
    PEER_KEY = 3;
    IGTK = 4;
};

struct SetKeyDescriptor {
    // Specs specify a bit string, we use byte array.
    bytes key;
    uint16 key_id;
    KeyType key_type;
    array<uint8>:6 address;
    array<uint8>:8 rsc;
    array<uint8>:3 cipher_suite_oui;
    uint8 cipher_suite_type;
};

struct SetKeysRequest {
    vector<SetKeyDescriptor> keylist;
};

// MLME-DELETEKEYS.request (IEEE Std 802.11-2016 6.3.20.1)

struct DeleteKeyDescriptor {
    uint16 key_id;
    KeyType key_type;
    array<uint8>:6 address;
};

struct DeleteKeysRequest {
    vector<DeleteKeyDescriptor> keylist;
};

// MLME-EAPOL.request (IEEE Std 802.11-2016 6.3.22.1)

struct EapolRequest {
    array<uint8>:6 src_addr;
    array<uint8>:6 dst_addr;
    bytes data;
};

// MLME-EAPOL.confirm (IEEE Std 802.11-2016 6.3.22.2)

enum EapolResultCodes {
    SUCCESS = 0;
    TRANSMISSION_FAILURE = 1;
    //LAST = TRANSMISSION_FAILURE;
};

struct EapolConfirm {
    EapolResultCodes result_code;
};

// IEEE Std 802.11-2016, 9.4.2.98
struct MeshConfiguration {
    uint8 active_path_sel_proto_id;
    uint8 active_path_sel_metric_id;
    uint8 congest_ctrl_method_id;
    uint8 sync_method_id;
    uint8 auth_proto_id;
    uint8 mesh_formation_info;
    uint8 mesh_capability;
};

// Fields that are common between the MPM Open and Confirm actions
struct MeshPeeringCommon {
    array<uint8>:6 peer_sta_address;
    uint16 protocol_id;
    uint16 local_link_id;
    bytes:32 mesh_id;
    vector<uint8> rates;
    MeshConfiguration mesh_config;
    HtCapabilities? ht_cap;
    HtOperation? ht_op;
    VhtCapabilities? vht_cap;
    VhtOperation? vht_op;
};

// IEEE Std 802.11-2016, 9.6.16.2.2
struct MeshPeeringOpenAction {
    MeshPeeringCommon common;
};

// IEEE Std 802.11-2016, 9.6.16.3.2
struct MeshPeeringConfirmAction {
    MeshPeeringCommon common;
    uint16 aid;
    uint16 peer_link_id;
};

struct MeshPeeringParams {
    array<uint8>:6 peer_sta_address;
    uint16 local_aid;
    vector<uint8> rates;
    // TODO(gbonik): HT/VHT caps
};

struct GetMeshPathTableRequest {
    uint8 dummy;
};

// Because these methods rely on an external entity to provide a response, events are used instead
// of return values.
protocol MLME {
    // ==== 01xxxx: scanning ====
    // We deviate from the spec here in order to support incremental scan
    // results easily. We could stay closer to 802.11ai, but the protocol
    // that is described there is more difficult to implement correctly.

    // Initiate a scan transaction. The caller is responsible for filling
    // the `txn_id` field in `req` with a unique number that will be used
    // to identify the transaction.
    //
    // Zero or more `OnScanResult` events with a matching `txn_id` will be sent
    // in response.
    //
    // At the end on the transaction, whether it is successful or not,
    // a `OnScanEnd` event with a matching `txn_id` is guaranteed to be sent
    // in response (unless the channel is closed first).
    //
    // After `OnScanEnd`, no further events with the same `txn_id` shall be sent.
    StartScan(ScanRequest req);

    // An incremental scan result containing information about a single BSS.
    // Only one event per unique BSSID per transaction will be sent.
    -> OnScanResult(ScanResult result);

    // An event that signals the end of a scan transaction.
    -> OnScanEnd(ScanEnd end);

    // ====

    JoinReq(JoinRequest req);
    -> JoinConf(JoinConfirm resp);

    AuthenticateReq(AuthenticateRequest req);
    -> AuthenticateConf(AuthenticateConfirm resp);

    -> AuthenticateInd(AuthenticateIndication ind);
    AuthenticateResp(AuthenticateResponse resp);

    DeauthenticateReq(DeauthenticateRequest req);
    -> DeauthenticateConf(DeauthenticateConfirm resp);

    -> DeauthenticateInd(DeauthenticateIndication ind);

    AssociateReq(AssociateRequest req);
    -> AssociateConf(AssociateConfirm resp);

    -> AssociateInd(AssociateIndication ind);
    AssociateResp(AssociateResponse resp);

    DisassociateReq(DisassociateRequest req);
    -> DisassociateConf(DisassociateConfirm resp);

    -> DisassociateInd(DisassociateIndication ind);

    ResetReq(ResetRequest req);

    StartReq(StartRequest req);
    -> StartConf(StartConfirm resp);

    StopReq(StopRequest req);
    -> StopConf(StopConfirm resp);

    SetKeysReq(SetKeysRequest req);

    DeleteKeysReq(DeleteKeysRequest req);

    EapolReq(EapolRequest req);
    -> EapolConf(EapolConfirm resp);

    // The following are extensions to the 802.11 MLME SAP interface.

    // ==== Mesh ===
    -> IncomingMpOpenAction(MeshPeeringOpenAction action);
    SendMpOpenAction(MeshPeeringOpenAction action);
    -> IncomingMpConfirmAction(MeshPeeringConfirmAction action);
    SendMpConfirmAction(MeshPeeringConfirmAction action);

    MeshPeeringEstablished(MeshPeeringParams peering);

    GetMeshPathTableReq(GetMeshPathTableRequest req) -> (fuchsia.wlan.mesh.MeshPathTable table);

    -> SignalReport(SignalReportIndication ind);

    -> EapolInd(EapolIndication ind);
    SetControlledPort(SetControlledPortRequest req);

    QueryDeviceInfo() -> (DeviceInfo info);

    StatsQueryReq();
    -> StatsQueryResp(StatsQueryResponse resp);

    ListMinstrelPeers() -> (MinstrelListResponse resp);
    GetMinstrelStats(MinstrelStatsRequest req) -> (MinstrelStatsResponse resp);
};