sdk/fidl/fuchsia.wlan.phyimpl/phyimpl.fidl

// Copyright 2022 The Fuchsia Authors. All rights reserved.
// Use of this source code is governed by a BSD-style license that can be
// found in the LICENSE file.

/// Acronyms \
/// Iface:  Interface \
/// Phy:    Physical \
/// Mac:    Medium Access Control \
/// Sta:    Station \
/// Addr:   Address
@available(added=15)
library fuchsia.wlan.phyimpl;

using fuchsia.wlan.common;
using fuchsia.wlan.ieee80211 as ieee80211;
using zx;

const WLANPHY_ALPHA2_LEN uint8 = 2;

type WlanPhyCountry = flexible union {
    /// ISO Alpha-2 takes two octet alphabet characters.
    /// This needs to be expanded if at least one WLAN device driver or firmware
    /// requires more than two octets.
    1: alpha2 array<uint8, WLANPHY_ALPHA2_LEN>;
};

@available(added=HEAD)
type BtCoexistenceMode = flexible enum {
    MODE_AUTO = 1;
    MODE_OFF = 2;
};

@discoverable
@transport("Driver")
open protocol WlanPhyImpl {
    /// MAC roles supported for ifaces on the physical device.
    flexible GetSupportedMacRoles() -> (table {
        1: supported_mac_roles
                vector<fuchsia.wlan.common.WlanMacRole>:fuchsia.wlan.common.MAX_SUPPORTED_MAC_ROLES;
    }) error zx.Status;

    /// Create a new interface with the specified role, returning the interface id. \
    /// Some common error codes are: \
    /// ZX_ERR_NO_RESOURCES: maximum number of interfaces have already been created. \
    /// ZX_ERR_NOT_SUPPORTED: device does not support the specified role.
    flexible CreateIface(resource table {
        /// The station role for this interface. A device may support multiple roles,
        /// but an interface is instantiated with a single role. This field is required.
        1: role fuchsia.wlan.common.WlanMacRole;
        /// A handle to the direct MLME channel, if supported by the driver. This
        /// channel should be used by SME to communicate with MLME via the MLME
        /// protocol. This field is required.
        2: mlme_channel zx.Handle:CHANNEL;
        /// The initial station address set from configuration layer. This field is optional.
        3: init_sta_addr ieee80211.MacAddr;
    }) -> (table {
        /// This field is always present.
        1: iface_id uint16;
    }) error zx.Status;

    /// Destroy the interface with the matching id. \
    /// Some common error codes are: \
    /// ZX_ERR_NOT_FOUND: Specified iface does not exist or has already been removed. \
    /// ZX_ERR_SHOULD_WAIT: Device is busy and cannot be removed, try again later.
    flexible DestroyIface(table {
        /// This field is required.
        1: iface_id uint16;
    }) -> () error zx.Status;

    /// Set country with a WlanPhyCountry. \
    /// Some common error codes are: \
    /// ZX_ERR_NOT_FOUND: Specified country code not supported. PHY state is left unchanged.
    flexible SetCountry(WlanPhyCountry) -> () error zx.Status;

    /// Set device to a world-safe country, i.e. a mode that conforms to all
    /// regulatory constraints globally. \
    /// Generally expected to succeed if the device is in a functional state.
    flexible ClearCountry() -> () error zx.Status;

    /// Read currently configured country. Implementations are advised to read the
    /// country directly from the firmware, where possible. \
    /// Generally expected to succeed if the device is in a functional state.
    flexible GetCountry() -> (WlanPhyCountry) error zx.Status;

    /// Set Power Save mode on device. In most implementations this
    /// likely to be set in Firmware. \
    /// Some common error codes are: \
    /// ZX_ERR_NOT_SUPPORTED: Specified Power Save mode not supported.
    flexible SetPowerSaveMode(table {
        /// This field is required.
        1: ps_mode fuchsia.wlan.common.PowerSaveType;
    }) -> () error zx.Status;

    /// Get current Power Save mode from device. In most implementation this
    /// likely to be retrieved from Firmware.
    flexible GetPowerSaveMode() -> (table {
        /// This field is required.
        1: ps_mode fuchsia.wlan.common.PowerSaveType;
    }) error zx.Status;

    /// Power up/down/reset the wlan chip.
    /// If supported, PowerDown will power down the wlan chip if it is currently powered on.
    /// Any existing interfaces should have already been deleted before making this call or else the
    /// driver will fail the call with error code ZX_ERR_INTERNAL.
    /// Other possible error codes are: \
    /// ZX_ERR_NOT_SUPPORTED: the feature is not supported by the driver.
    /// ZX_ERR_BAD_STATE: the wlan chip is already powered down.
    @available(added=HEAD)
    flexible PowerDown() -> () error zx.Status;

    /// If supported, PowerUp will power up the wlan chip if it is currently powered down.
    /// Possible error codes are: \
    /// ZX_ERR_NOT_SUPPORTED: the feature is not supported by the driver.
    /// ZX_ERR_BAD_STATE: the wlan chip is already powered up.
    @available(added=HEAD)
    flexible PowerUp() -> () error zx.Status;

    /// If supported, Reset functionality implements PowerDown then PowerUp in an attempt to
    /// recover from an error state. For example, if an interface gets into a bad state or if
    /// firmware crashes, the firmware/chip may be unable to perform some actions and Reset
    /// may be able to clear the bad state.
    /// Possible error codes are: \
    /// ZX_ERR_NOT_SUPPORTED: the feature is not supported by the driver.
    @available(added=HEAD)
    flexible Reset() -> () error zx.Status;

    /// Returns the current power state of the wlan chip. After successful initialization
    /// of the wlan driver, the state is set to true (power on) by default. power_on set to
    /// true indicates that the wlan chip is powered on and false indicates the wlan chip
    /// is powered off.
    @available(added=HEAD)
    flexible GetPowerState() -> (table {
        1: power_on bool;
    }) error zx.Status;

    /// Set the Bluetooth coexistence mode.
    /// Possible error codes are: \
    /// ZX_ERR_NOT_SUPPORTED: device does not support the specified BT coexistence mode.
    @available(added=HEAD)
    flexible SetBtCoexistenceMode(table {
        1: mode BtCoexistenceMode;
    }) -> () error zx.Status;
};

service Service {
    wlan_phy_impl client_end:WlanPhyImpl;
};