blob: 40dc0e4c76db772871e5336c349fc9c587d14b2d [file] [log] [blame]
/*
* OpenPOWER Palmetto BMC
*
* Andrew Jeffery <andrew@aj.id.au>
*
* Copyright 2016 IBM Corp.
*
* This code is licensed under the GPL version 2 or later. See
* the COPYING file in the top-level directory.
*/
#include "qemu/osdep.h"
#include "qapi/error.h"
#include "hw/arm/boot.h"
#include "hw/arm/aspeed.h"
#include "hw/arm/aspeed_soc.h"
#include "hw/arm/aspeed_eeprom.h"
#include "hw/block/flash.h"
#include "hw/i2c/i2c_mux_pca954x.h"
#include "hw/i2c/smbus_eeprom.h"
#include "hw/gpio/pca9552.h"
#include "hw/nvram/eeprom_at24c.h"
#include "hw/sensor/tmp105.h"
#include "hw/misc/led.h"
#include "hw/qdev-properties.h"
#include "sysemu/block-backend.h"
#include "sysemu/reset.h"
#include "hw/loader.h"
#include "qemu/error-report.h"
#include "qemu/units.h"
#include "hw/qdev-clock.h"
#include "sysemu/sysemu.h"
static struct arm_boot_info aspeed_board_binfo = {
.board_id = -1, /* device-tree-only board */
};
struct AspeedMachineState {
/* Private */
MachineState parent_obj;
/* Public */
AspeedSoCState *soc;
MemoryRegion boot_rom;
bool mmio_exec;
uint32_t uart_chosen;
char *fmc_model;
char *spi_model;
};
/* On 32-bit hosts, lower RAM to 1G because of the 2047 MB limit */
#if HOST_LONG_BITS == 32
#define ASPEED_RAM_SIZE(sz) MIN((sz), 1 * GiB)
#else
#define ASPEED_RAM_SIZE(sz) (sz)
#endif
/* Palmetto hardware value: 0x120CE416 */
#define PALMETTO_BMC_HW_STRAP1 ( \
SCU_AST2400_HW_STRAP_DRAM_SIZE(DRAM_SIZE_256MB) | \
SCU_AST2400_HW_STRAP_DRAM_CONFIG(2 /* DDR3 with CL=6, CWL=5 */) | \
SCU_AST2400_HW_STRAP_ACPI_DIS | \
SCU_AST2400_HW_STRAP_SET_CLK_SOURCE(AST2400_CLK_48M_IN) | \
SCU_HW_STRAP_VGA_CLASS_CODE | \
SCU_HW_STRAP_LPC_RESET_PIN | \
SCU_HW_STRAP_SPI_MODE(SCU_HW_STRAP_SPI_M_S_EN) | \
SCU_AST2400_HW_STRAP_SET_CPU_AHB_RATIO(AST2400_CPU_AHB_RATIO_2_1) | \
SCU_HW_STRAP_SPI_WIDTH | \
SCU_HW_STRAP_VGA_SIZE_SET(VGA_16M_DRAM) | \
SCU_AST2400_HW_STRAP_BOOT_MODE(AST2400_SPI_BOOT))
/* TODO: Find the actual hardware value */
#define SUPERMICROX11_BMC_HW_STRAP1 ( \
SCU_AST2400_HW_STRAP_DRAM_SIZE(DRAM_SIZE_128MB) | \
SCU_AST2400_HW_STRAP_DRAM_CONFIG(2) | \
SCU_AST2400_HW_STRAP_ACPI_DIS | \
SCU_AST2400_HW_STRAP_SET_CLK_SOURCE(AST2400_CLK_48M_IN) | \
SCU_HW_STRAP_VGA_CLASS_CODE | \
SCU_HW_STRAP_LPC_RESET_PIN | \
SCU_HW_STRAP_SPI_MODE(SCU_HW_STRAP_SPI_M_S_EN) | \
SCU_AST2400_HW_STRAP_SET_CPU_AHB_RATIO(AST2400_CPU_AHB_RATIO_2_1) | \
SCU_HW_STRAP_SPI_WIDTH | \
SCU_HW_STRAP_VGA_SIZE_SET(VGA_16M_DRAM) | \
SCU_AST2400_HW_STRAP_BOOT_MODE(AST2400_SPI_BOOT))
/* TODO: Find the actual hardware value */
#define SUPERMICRO_X11SPI_BMC_HW_STRAP1 ( \
AST2500_HW_STRAP1_DEFAULTS | \
SCU_AST2500_HW_STRAP_SPI_AUTOFETCH_ENABLE | \
SCU_AST2500_HW_STRAP_GPIO_STRAP_ENABLE | \
SCU_AST2500_HW_STRAP_UART_DEBUG | \
SCU_AST2500_HW_STRAP_DDR4_ENABLE | \
SCU_HW_STRAP_SPI_WIDTH | \
SCU_HW_STRAP_SPI_MODE(SCU_HW_STRAP_SPI_M_S_EN))
/* AST2500 evb hardware value: 0xF100C2E6 */
#define AST2500_EVB_HW_STRAP1 (( \
AST2500_HW_STRAP1_DEFAULTS | \
SCU_AST2500_HW_STRAP_SPI_AUTOFETCH_ENABLE | \
SCU_AST2500_HW_STRAP_GPIO_STRAP_ENABLE | \
SCU_AST2500_HW_STRAP_UART_DEBUG | \
SCU_AST2500_HW_STRAP_DDR4_ENABLE | \
SCU_HW_STRAP_MAC1_RGMII | \
SCU_HW_STRAP_MAC0_RGMII) & \
~SCU_HW_STRAP_2ND_BOOT_WDT)
/* Romulus hardware value: 0xF10AD206 */
#define ROMULUS_BMC_HW_STRAP1 ( \
AST2500_HW_STRAP1_DEFAULTS | \
SCU_AST2500_HW_STRAP_SPI_AUTOFETCH_ENABLE | \
SCU_AST2500_HW_STRAP_GPIO_STRAP_ENABLE | \
SCU_AST2500_HW_STRAP_UART_DEBUG | \
SCU_AST2500_HW_STRAP_DDR4_ENABLE | \
SCU_AST2500_HW_STRAP_ACPI_ENABLE | \
SCU_HW_STRAP_SPI_MODE(SCU_HW_STRAP_SPI_MASTER))
/* Sonorapass hardware value: 0xF100D216 */
#define SONORAPASS_BMC_HW_STRAP1 ( \
SCU_AST2500_HW_STRAP_SPI_AUTOFETCH_ENABLE | \
SCU_AST2500_HW_STRAP_GPIO_STRAP_ENABLE | \
SCU_AST2500_HW_STRAP_UART_DEBUG | \
SCU_AST2500_HW_STRAP_RESERVED28 | \
SCU_AST2500_HW_STRAP_DDR4_ENABLE | \
SCU_HW_STRAP_VGA_CLASS_CODE | \
SCU_HW_STRAP_LPC_RESET_PIN | \
SCU_HW_STRAP_SPI_MODE(SCU_HW_STRAP_SPI_MASTER) | \
SCU_AST2500_HW_STRAP_SET_AXI_AHB_RATIO(AXI_AHB_RATIO_2_1) | \
SCU_HW_STRAP_VGA_BIOS_ROM | \
SCU_HW_STRAP_VGA_SIZE_SET(VGA_16M_DRAM) | \
SCU_AST2500_HW_STRAP_RESERVED1)
#define G220A_BMC_HW_STRAP1 ( \
SCU_AST2500_HW_STRAP_SPI_AUTOFETCH_ENABLE | \
SCU_AST2500_HW_STRAP_GPIO_STRAP_ENABLE | \
SCU_AST2500_HW_STRAP_UART_DEBUG | \
SCU_AST2500_HW_STRAP_RESERVED28 | \
SCU_AST2500_HW_STRAP_DDR4_ENABLE | \
SCU_HW_STRAP_2ND_BOOT_WDT | \
SCU_HW_STRAP_VGA_CLASS_CODE | \
SCU_HW_STRAP_LPC_RESET_PIN | \
SCU_HW_STRAP_SPI_MODE(SCU_HW_STRAP_SPI_MASTER) | \
SCU_AST2500_HW_STRAP_SET_AXI_AHB_RATIO(AXI_AHB_RATIO_2_1) | \
SCU_HW_STRAP_VGA_SIZE_SET(VGA_64M_DRAM) | \
SCU_AST2500_HW_STRAP_RESERVED1)
/* FP5280G2 hardware value: 0XF100D286 */
#define FP5280G2_BMC_HW_STRAP1 ( \
SCU_AST2500_HW_STRAP_SPI_AUTOFETCH_ENABLE | \
SCU_AST2500_HW_STRAP_GPIO_STRAP_ENABLE | \
SCU_AST2500_HW_STRAP_UART_DEBUG | \
SCU_AST2500_HW_STRAP_RESERVED28 | \
SCU_AST2500_HW_STRAP_DDR4_ENABLE | \
SCU_HW_STRAP_VGA_CLASS_CODE | \
SCU_HW_STRAP_LPC_RESET_PIN | \
SCU_HW_STRAP_SPI_MODE(SCU_HW_STRAP_SPI_MASTER) | \
SCU_AST2500_HW_STRAP_SET_AXI_AHB_RATIO(AXI_AHB_RATIO_2_1) | \
SCU_HW_STRAP_MAC1_RGMII | \
SCU_HW_STRAP_VGA_SIZE_SET(VGA_16M_DRAM) | \
SCU_AST2500_HW_STRAP_RESERVED1)
/* Witherspoon hardware value: 0xF10AD216 (but use romulus definition) */
#define WITHERSPOON_BMC_HW_STRAP1 ROMULUS_BMC_HW_STRAP1
/* Quanta-Q71l hardware value */
#define QUANTA_Q71L_BMC_HW_STRAP1 ( \
SCU_AST2400_HW_STRAP_DRAM_SIZE(DRAM_SIZE_128MB) | \
SCU_AST2400_HW_STRAP_DRAM_CONFIG(2/* DDR3 with CL=6, CWL=5 */) | \
SCU_AST2400_HW_STRAP_ACPI_DIS | \
SCU_AST2400_HW_STRAP_SET_CLK_SOURCE(AST2400_CLK_24M_IN) | \
SCU_HW_STRAP_VGA_CLASS_CODE | \
SCU_HW_STRAP_SPI_MODE(SCU_HW_STRAP_SPI_PASS_THROUGH) | \
SCU_AST2400_HW_STRAP_SET_CPU_AHB_RATIO(AST2400_CPU_AHB_RATIO_2_1) | \
SCU_HW_STRAP_SPI_WIDTH | \
SCU_HW_STRAP_VGA_SIZE_SET(VGA_8M_DRAM) | \
SCU_AST2400_HW_STRAP_BOOT_MODE(AST2400_SPI_BOOT))
/* AST2600 evb hardware value */
#define AST2600_EVB_HW_STRAP1 0x000000C0
#define AST2600_EVB_HW_STRAP2 0x00000003
#ifdef TARGET_AARCH64
/* AST2700 evb hardware value */
#define AST2700_EVB_HW_STRAP1 0x000000C0
#define AST2700_EVB_HW_STRAP2 0x00000003
#endif
/* Tacoma hardware value */
#define TACOMA_BMC_HW_STRAP1 0x00000000
#define TACOMA_BMC_HW_STRAP2 0x00000040
/* Rainier hardware value: (QEMU prototype) */
#define RAINIER_BMC_HW_STRAP1 0x00422016
#define RAINIER_BMC_HW_STRAP2 0x80000848
/* Fuji hardware value */
#define FUJI_BMC_HW_STRAP1 0x00000000
#define FUJI_BMC_HW_STRAP2 0x00000000
/* Bletchley hardware value */
/* TODO: Leave same as EVB for now. */
#define BLETCHLEY_BMC_HW_STRAP1 AST2600_EVB_HW_STRAP1
#define BLETCHLEY_BMC_HW_STRAP2 AST2600_EVB_HW_STRAP2
/* Qualcomm DC-SCM hardware value */
#define QCOM_DC_SCM_V1_BMC_HW_STRAP1 0x00000000
#define QCOM_DC_SCM_V1_BMC_HW_STRAP2 0x00000041
#define AST_SMP_MAILBOX_BASE 0x1e6e2180
#define AST_SMP_MBOX_FIELD_ENTRY (AST_SMP_MAILBOX_BASE + 0x0)
#define AST_SMP_MBOX_FIELD_GOSIGN (AST_SMP_MAILBOX_BASE + 0x4)
#define AST_SMP_MBOX_FIELD_READY (AST_SMP_MAILBOX_BASE + 0x8)
#define AST_SMP_MBOX_FIELD_POLLINSN (AST_SMP_MAILBOX_BASE + 0xc)
#define AST_SMP_MBOX_CODE (AST_SMP_MAILBOX_BASE + 0x10)
#define AST_SMP_MBOX_GOSIGN 0xabbaab00
static void aspeed_write_smpboot(ARMCPU *cpu,
const struct arm_boot_info *info)
{
AddressSpace *as = arm_boot_address_space(cpu, info);
static const ARMInsnFixup poll_mailbox_ready[] = {
/*
* r2 = per-cpu go sign value
* r1 = AST_SMP_MBOX_FIELD_ENTRY
* r0 = AST_SMP_MBOX_FIELD_GOSIGN
*/
{ 0xee100fb0 }, /* mrc p15, 0, r0, c0, c0, 5 */
{ 0xe21000ff }, /* ands r0, r0, #255 */
{ 0xe59f201c }, /* ldr r2, [pc, #28] */
{ 0xe1822000 }, /* orr r2, r2, r0 */
{ 0xe59f1018 }, /* ldr r1, [pc, #24] */
{ 0xe59f0018 }, /* ldr r0, [pc, #24] */
{ 0xe320f002 }, /* wfe */
{ 0xe5904000 }, /* ldr r4, [r0] */
{ 0xe1520004 }, /* cmp r2, r4 */
{ 0x1afffffb }, /* bne <wfe> */
{ 0xe591f000 }, /* ldr pc, [r1] */
{ AST_SMP_MBOX_GOSIGN },
{ AST_SMP_MBOX_FIELD_ENTRY },
{ AST_SMP_MBOX_FIELD_GOSIGN },
{ 0, FIXUP_TERMINATOR }
};
static const uint32_t fixupcontext[FIXUP_MAX] = { 0 };
arm_write_bootloader("aspeed.smpboot", as, info->smp_loader_start,
poll_mailbox_ready, fixupcontext);
}
static void aspeed_reset_secondary(ARMCPU *cpu,
const struct arm_boot_info *info)
{
AddressSpace *as = arm_boot_address_space(cpu, info);
CPUState *cs = CPU(cpu);
/* info->smp_bootreg_addr */
address_space_stl_notdirty(as, AST_SMP_MBOX_FIELD_GOSIGN, 0,
MEMTXATTRS_UNSPECIFIED, NULL);
cpu_set_pc(cs, info->smp_loader_start);
}
static void write_boot_rom(BlockBackend *blk, hwaddr addr, size_t rom_size,
Error **errp)
{
g_autofree void *storage = NULL;
int64_t size;
/* The block backend size should have already been 'validated' by
* the creation of the m25p80 object.
*/
size = blk_getlength(blk);
if (size <= 0) {
error_setg(errp, "failed to get flash size");
return;
}
if (rom_size > size) {
rom_size = size;
}
storage = g_malloc0(rom_size);
if (blk_pread(blk, 0, rom_size, storage, 0) < 0) {
error_setg(errp, "failed to read the initial flash content");
return;
}
rom_add_blob_fixed("aspeed.boot_rom", storage, rom_size, addr);
}
/*
* Create a ROM and copy the flash contents at the expected address
* (0x0). Boots faster than execute-in-place.
*/
static void aspeed_install_boot_rom(AspeedMachineState *bmc, BlockBackend *blk,
uint64_t rom_size)
{
AspeedSoCState *soc = bmc->soc;
AspeedSoCClass *sc = ASPEED_SOC_GET_CLASS(soc);
memory_region_init_rom(&bmc->boot_rom, NULL, "aspeed.boot_rom", rom_size,
&error_abort);
memory_region_add_subregion_overlap(&soc->spi_boot_container, 0,
&bmc->boot_rom, 1);
write_boot_rom(blk, sc->memmap[ASPEED_DEV_SPI_BOOT],
rom_size, &error_abort);
}
void aspeed_board_init_flashes(AspeedSMCState *s, const char *flashtype,
unsigned int count, int unit0)
{
int i;
if (!flashtype) {
return;
}
for (i = 0; i < count; ++i) {
DriveInfo *dinfo = drive_get(IF_MTD, 0, unit0 + i);
DeviceState *dev;
dev = qdev_new(flashtype);
if (dinfo) {
qdev_prop_set_drive(dev, "drive", blk_by_legacy_dinfo(dinfo));
}
qdev_prop_set_uint8(dev, "cs", i);
qdev_realize_and_unref(dev, BUS(s->spi), &error_fatal);
}
}
static void sdhci_attach_drive(SDHCIState *sdhci, DriveInfo *dinfo)
{
DeviceState *card;
if (!dinfo) {
return;
}
card = qdev_new(TYPE_SD_CARD);
qdev_prop_set_drive_err(card, "drive", blk_by_legacy_dinfo(dinfo),
&error_fatal);
qdev_realize_and_unref(card,
qdev_get_child_bus(DEVICE(sdhci), "sd-bus"),
&error_fatal);
}
static void connect_serial_hds_to_uarts(AspeedMachineState *bmc)
{
AspeedMachineClass *amc = ASPEED_MACHINE_GET_CLASS(bmc);
AspeedSoCState *s = bmc->soc;
AspeedSoCClass *sc = ASPEED_SOC_GET_CLASS(s);
int uart_chosen = bmc->uart_chosen ? bmc->uart_chosen : amc->uart_default;
aspeed_soc_uart_set_chr(s, uart_chosen, serial_hd(0));
for (int i = 1, uart = sc->uarts_base; i < sc->uarts_num; i++, uart++) {
if (uart == uart_chosen) {
continue;
}
aspeed_soc_uart_set_chr(s, uart, serial_hd(i));
}
}
static void aspeed_machine_init(MachineState *machine)
{
AspeedMachineState *bmc = ASPEED_MACHINE(machine);
AspeedMachineClass *amc = ASPEED_MACHINE_GET_CLASS(machine);
AspeedSoCClass *sc;
int i;
bmc->soc = ASPEED_SOC(object_new(amc->soc_name));
object_property_add_child(OBJECT(machine), "soc", OBJECT(bmc->soc));
object_unref(OBJECT(bmc->soc));
sc = ASPEED_SOC_GET_CLASS(bmc->soc);
/*
* This will error out if the RAM size is not supported by the
* memory controller of the SoC.
*/
object_property_set_uint(OBJECT(bmc->soc), "ram-size", machine->ram_size,
&error_fatal);
for (i = 0; i < sc->macs_num; i++) {
if ((amc->macs_mask & (1 << i)) &&
!qemu_configure_nic_device(DEVICE(&bmc->soc->ftgmac100[i]),
true, NULL)) {
break; /* No configs left; stop asking */
}
}
object_property_set_int(OBJECT(bmc->soc), "hw-strap1", amc->hw_strap1,
&error_abort);
object_property_set_int(OBJECT(bmc->soc), "hw-strap2", amc->hw_strap2,
&error_abort);
object_property_set_link(OBJECT(bmc->soc), "memory",
OBJECT(get_system_memory()), &error_abort);
object_property_set_link(OBJECT(bmc->soc), "dram",
OBJECT(machine->ram), &error_abort);
if (machine->kernel_filename) {
/*
* When booting with a -kernel command line there is no u-boot
* that runs to unlock the SCU. In this case set the default to
* be unlocked as the kernel expects
*/
object_property_set_int(OBJECT(bmc->soc), "hw-prot-key",
ASPEED_SCU_PROT_KEY, &error_abort);
}
connect_serial_hds_to_uarts(bmc);
qdev_realize(DEVICE(bmc->soc), NULL, &error_abort);
if (defaults_enabled()) {
aspeed_board_init_flashes(&bmc->soc->fmc,
bmc->fmc_model ? bmc->fmc_model : amc->fmc_model,
amc->num_cs, 0);
aspeed_board_init_flashes(&bmc->soc->spi[0],
bmc->spi_model ? bmc->spi_model : amc->spi_model,
1, amc->num_cs);
}
if (machine->kernel_filename && sc->num_cpus > 1) {
/* With no u-boot we must set up a boot stub for the secondary CPU */
MemoryRegion *smpboot = g_new(MemoryRegion, 1);
memory_region_init_ram(smpboot, NULL, "aspeed.smpboot",
0x80, &error_abort);
memory_region_add_subregion(get_system_memory(),
AST_SMP_MAILBOX_BASE, smpboot);
aspeed_board_binfo.write_secondary_boot = aspeed_write_smpboot;
aspeed_board_binfo.secondary_cpu_reset_hook = aspeed_reset_secondary;
aspeed_board_binfo.smp_loader_start = AST_SMP_MBOX_CODE;
}
aspeed_board_binfo.ram_size = machine->ram_size;
aspeed_board_binfo.loader_start = sc->memmap[ASPEED_DEV_SDRAM];
if (amc->i2c_init) {
amc->i2c_init(bmc);
}
for (i = 0; i < bmc->soc->sdhci.num_slots; i++) {
sdhci_attach_drive(&bmc->soc->sdhci.slots[i],
drive_get(IF_SD, 0, i));
}
if (bmc->soc->emmc.num_slots) {
sdhci_attach_drive(&bmc->soc->emmc.slots[0],
drive_get(IF_SD, 0, bmc->soc->sdhci.num_slots));
}
if (!bmc->mmio_exec) {
DeviceState *dev = ssi_get_cs(bmc->soc->fmc.spi, 0);
BlockBackend *fmc0 = dev ? m25p80_get_blk(dev) : NULL;
if (fmc0) {
uint64_t rom_size = memory_region_size(&bmc->soc->spi_boot);
aspeed_install_boot_rom(bmc, fmc0, rom_size);
}
}
arm_load_kernel(ARM_CPU(first_cpu), machine, &aspeed_board_binfo);
}
static void palmetto_bmc_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
DeviceState *dev;
uint8_t *eeprom_buf = g_malloc0(32 * 1024);
/* The palmetto platform expects a ds3231 RTC but a ds1338 is
* enough to provide basic RTC features. Alarms will be missing */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 0), "ds1338", 0x68);
smbus_eeprom_init_one(aspeed_i2c_get_bus(&soc->i2c, 0), 0x50,
eeprom_buf);
/* add a TMP423 temperature sensor */
dev = DEVICE(i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 2),
"tmp423", 0x4c));
object_property_set_int(OBJECT(dev), "temperature0", 31000, &error_abort);
object_property_set_int(OBJECT(dev), "temperature1", 28000, &error_abort);
object_property_set_int(OBJECT(dev), "temperature2", 20000, &error_abort);
object_property_set_int(OBJECT(dev), "temperature3", 110000, &error_abort);
}
static void quanta_q71l_bmc_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
/*
* The quanta-q71l platform expects tmp75s which are compatible with
* tmp105s.
*/
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 1), "tmp105", 0x4c);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 1), "tmp105", 0x4e);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 1), "tmp105", 0x4f);
/* TODO: i2c-1: Add baseboard FRU eeprom@54 24c64 */
/* TODO: i2c-1: Add Frontpanel FRU eeprom@57 24c64 */
/* TODO: Add Memory Riser i2c mux and eeproms. */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 2), "pca9546", 0x74);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 2), "pca9548", 0x77);
/* TODO: i2c-3: Add BIOS FRU eeprom@56 24c64 */
/* i2c-7 */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 7), "pca9546", 0x70);
/* - i2c@0: pmbus@59 */
/* - i2c@1: pmbus@58 */
/* - i2c@2: pmbus@58 */
/* - i2c@3: pmbus@59 */
/* TODO: i2c-7: Add PDB FRU eeprom@52 */
/* TODO: i2c-8: Add BMC FRU eeprom@50 */
}
static void ast2500_evb_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
uint8_t *eeprom_buf = g_malloc0(8 * 1024);
smbus_eeprom_init_one(aspeed_i2c_get_bus(&soc->i2c, 3), 0x50,
eeprom_buf);
/* The AST2500 EVB expects a LM75 but a TMP105 is compatible */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 7),
TYPE_TMP105, 0x4d);
}
static void ast2600_evb_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
uint8_t *eeprom_buf = g_malloc0(8 * 1024);
smbus_eeprom_init_one(aspeed_i2c_get_bus(&soc->i2c, 7), 0x50,
eeprom_buf);
/* LM75 is compatible with TMP105 driver */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 8),
TYPE_TMP105, 0x4d);
}
static void yosemitev2_bmc_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
at24c_eeprom_init(aspeed_i2c_get_bus(&soc->i2c, 4), 0x51, 128 * KiB);
at24c_eeprom_init_rom(aspeed_i2c_get_bus(&soc->i2c, 8), 0x51, 128 * KiB,
yosemitev2_bmc_fruid, yosemitev2_bmc_fruid_len);
/* TMP421 */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 11), "tmp421", 0x1f);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 9), "tmp421", 0x4e);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 9), "tmp421", 0x4f);
}
static void romulus_bmc_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
/* The romulus board expects Epson RX8900 I2C RTC but a ds1338 is
* good enough */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 11), "ds1338", 0x32);
}
static void tiogapass_bmc_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
at24c_eeprom_init(aspeed_i2c_get_bus(&soc->i2c, 4), 0x54, 128 * KiB);
at24c_eeprom_init_rom(aspeed_i2c_get_bus(&soc->i2c, 6), 0x54, 128 * KiB,
tiogapass_bmc_fruid, tiogapass_bmc_fruid_len);
/* TMP421 */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 8), "tmp421", 0x1f);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 6), "tmp421", 0x4f);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 6), "tmp421", 0x4e);
}
static void create_pca9552(AspeedSoCState *soc, int bus_id, int addr)
{
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, bus_id),
TYPE_PCA9552, addr);
}
static void sonorapass_bmc_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
/* bus 2 : */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 2), "tmp105", 0x48);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 2), "tmp105", 0x49);
/* bus 2 : pca9546 @ 0x73 */
/* bus 3 : pca9548 @ 0x70 */
/* bus 4 : */
uint8_t *eeprom4_54 = g_malloc0(8 * 1024);
smbus_eeprom_init_one(aspeed_i2c_get_bus(&soc->i2c, 4), 0x54,
eeprom4_54);
/* PCA9539 @ 0x76, but PCA9552 is compatible */
create_pca9552(soc, 4, 0x76);
/* PCA9539 @ 0x77, but PCA9552 is compatible */
create_pca9552(soc, 4, 0x77);
/* bus 6 : */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 6), "tmp105", 0x48);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 6), "tmp105", 0x49);
/* bus 6 : pca9546 @ 0x73 */
/* bus 8 : */
uint8_t *eeprom8_56 = g_malloc0(8 * 1024);
smbus_eeprom_init_one(aspeed_i2c_get_bus(&soc->i2c, 8), 0x56,
eeprom8_56);
create_pca9552(soc, 8, 0x60);
create_pca9552(soc, 8, 0x61);
/* bus 8 : adc128d818 @ 0x1d */
/* bus 8 : adc128d818 @ 0x1f */
/*
* bus 13 : pca9548 @ 0x71
* - channel 3:
* - tmm421 @ 0x4c
* - tmp421 @ 0x4e
* - tmp421 @ 0x4f
*/
}
static void witherspoon_bmc_i2c_init(AspeedMachineState *bmc)
{
static const struct {
unsigned gpio_id;
LEDColor color;
const char *description;
bool gpio_polarity;
} pca1_leds[] = {
{13, LED_COLOR_GREEN, "front-fault-4", GPIO_POLARITY_ACTIVE_LOW},
{14, LED_COLOR_GREEN, "front-power-3", GPIO_POLARITY_ACTIVE_LOW},
{15, LED_COLOR_GREEN, "front-id-5", GPIO_POLARITY_ACTIVE_LOW},
};
AspeedSoCState *soc = bmc->soc;
uint8_t *eeprom_buf = g_malloc0(8 * 1024);
DeviceState *dev;
LEDState *led;
/* Bus 3: TODO bmp280@77 */
dev = DEVICE(i2c_slave_new(TYPE_PCA9552, 0x60));
qdev_prop_set_string(dev, "description", "pca1");
i2c_slave_realize_and_unref(I2C_SLAVE(dev),
aspeed_i2c_get_bus(&soc->i2c, 3),
&error_fatal);
for (size_t i = 0; i < ARRAY_SIZE(pca1_leds); i++) {
led = led_create_simple(OBJECT(bmc),
pca1_leds[i].gpio_polarity,
pca1_leds[i].color,
pca1_leds[i].description);
qdev_connect_gpio_out(dev, pca1_leds[i].gpio_id,
qdev_get_gpio_in(DEVICE(led), 0));
}
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 3), "dps310", 0x76);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 3), "max31785", 0x52);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 4), "tmp423", 0x4c);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 5), "tmp423", 0x4c);
/* The Witherspoon expects a TMP275 but a TMP105 is compatible */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 9), TYPE_TMP105,
0x4a);
/* The witherspoon board expects Epson RX8900 I2C RTC but a ds1338 is
* good enough */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 11), "ds1338", 0x32);
smbus_eeprom_init_one(aspeed_i2c_get_bus(&soc->i2c, 11), 0x51,
eeprom_buf);
dev = DEVICE(i2c_slave_new(TYPE_PCA9552, 0x60));
qdev_prop_set_string(dev, "description", "pca0");
i2c_slave_realize_and_unref(I2C_SLAVE(dev),
aspeed_i2c_get_bus(&soc->i2c, 11),
&error_fatal);
/* Bus 11: TODO ucd90160@64 */
}
static void g220a_bmc_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
DeviceState *dev;
dev = DEVICE(i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 3),
"emc1413", 0x4c));
object_property_set_int(OBJECT(dev), "temperature0", 31000, &error_abort);
object_property_set_int(OBJECT(dev), "temperature1", 28000, &error_abort);
object_property_set_int(OBJECT(dev), "temperature2", 20000, &error_abort);
dev = DEVICE(i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 12),
"emc1413", 0x4c));
object_property_set_int(OBJECT(dev), "temperature0", 31000, &error_abort);
object_property_set_int(OBJECT(dev), "temperature1", 28000, &error_abort);
object_property_set_int(OBJECT(dev), "temperature2", 20000, &error_abort);
dev = DEVICE(i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 13),
"emc1413", 0x4c));
object_property_set_int(OBJECT(dev), "temperature0", 31000, &error_abort);
object_property_set_int(OBJECT(dev), "temperature1", 28000, &error_abort);
object_property_set_int(OBJECT(dev), "temperature2", 20000, &error_abort);
static uint8_t eeprom_buf[2 * 1024] = {
0x01, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0xfe,
0x01, 0x06, 0x00, 0xc9, 0x42, 0x79, 0x74, 0x65,
0x64, 0x61, 0x6e, 0x63, 0x65, 0xc5, 0x47, 0x32,
0x32, 0x30, 0x41, 0xc4, 0x41, 0x41, 0x42, 0x42,
0xc4, 0x43, 0x43, 0x44, 0x44, 0xc4, 0x45, 0x45,
0x46, 0x46, 0xc4, 0x48, 0x48, 0x47, 0x47, 0xc1,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xa7,
};
smbus_eeprom_init_one(aspeed_i2c_get_bus(&soc->i2c, 4), 0x57,
eeprom_buf);
}
static void fp5280g2_bmc_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
I2CSlave *i2c_mux;
/* The at24c256 */
at24c_eeprom_init(aspeed_i2c_get_bus(&soc->i2c, 1), 0x50, 32768);
/* The fp5280g2 expects a TMP112 but a TMP105 is compatible */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 2), TYPE_TMP105,
0x48);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 2), TYPE_TMP105,
0x49);
i2c_mux = i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 2),
"pca9546", 0x70);
/* It expects a TMP112 but a TMP105 is compatible */
i2c_slave_create_simple(pca954x_i2c_get_bus(i2c_mux, 0), TYPE_TMP105,
0x4a);
/* It expects a ds3232 but a ds1338 is good enough */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 4), "ds1338", 0x68);
/* It expects a pca9555 but a pca9552 is compatible */
create_pca9552(soc, 8, 0x30);
}
static void rainier_bmc_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
I2CSlave *i2c_mux;
at24c_eeprom_init(aspeed_i2c_get_bus(&soc->i2c, 0), 0x51, 32 * KiB);
create_pca9552(soc, 3, 0x61);
/* The rainier expects a TMP275 but a TMP105 is compatible */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 4), TYPE_TMP105,
0x48);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 4), TYPE_TMP105,
0x49);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 4), TYPE_TMP105,
0x4a);
i2c_mux = i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 4),
"pca9546", 0x70);
at24c_eeprom_init(pca954x_i2c_get_bus(i2c_mux, 0), 0x50, 64 * KiB);
at24c_eeprom_init(pca954x_i2c_get_bus(i2c_mux, 1), 0x51, 64 * KiB);
at24c_eeprom_init(pca954x_i2c_get_bus(i2c_mux, 2), 0x52, 64 * KiB);
create_pca9552(soc, 4, 0x60);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 5), TYPE_TMP105,
0x48);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 5), TYPE_TMP105,
0x49);
create_pca9552(soc, 5, 0x60);
create_pca9552(soc, 5, 0x61);
i2c_mux = i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 5),
"pca9546", 0x70);
at24c_eeprom_init(pca954x_i2c_get_bus(i2c_mux, 0), 0x50, 64 * KiB);
at24c_eeprom_init(pca954x_i2c_get_bus(i2c_mux, 1), 0x51, 64 * KiB);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 6), TYPE_TMP105,
0x48);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 6), TYPE_TMP105,
0x4a);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 6), TYPE_TMP105,
0x4b);
i2c_mux = i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 6),
"pca9546", 0x70);
at24c_eeprom_init(pca954x_i2c_get_bus(i2c_mux, 0), 0x50, 64 * KiB);
at24c_eeprom_init(pca954x_i2c_get_bus(i2c_mux, 1), 0x51, 64 * KiB);
at24c_eeprom_init(pca954x_i2c_get_bus(i2c_mux, 2), 0x50, 64 * KiB);
at24c_eeprom_init(pca954x_i2c_get_bus(i2c_mux, 3), 0x51, 64 * KiB);
create_pca9552(soc, 7, 0x30);
create_pca9552(soc, 7, 0x31);
create_pca9552(soc, 7, 0x32);
create_pca9552(soc, 7, 0x33);
create_pca9552(soc, 7, 0x60);
create_pca9552(soc, 7, 0x61);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 7), "dps310", 0x76);
/* Bus 7: TODO si7021-a20@20 */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 7), TYPE_TMP105,
0x48);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 7), "max31785", 0x52);
at24c_eeprom_init(aspeed_i2c_get_bus(&soc->i2c, 7), 0x50, 64 * KiB);
at24c_eeprom_init(aspeed_i2c_get_bus(&soc->i2c, 7), 0x51, 64 * KiB);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 8), TYPE_TMP105,
0x48);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 8), TYPE_TMP105,
0x4a);
at24c_eeprom_init_rom(aspeed_i2c_get_bus(&soc->i2c, 8), 0x50,
64 * KiB, rainier_bb_fruid, rainier_bb_fruid_len);
at24c_eeprom_init_rom(aspeed_i2c_get_bus(&soc->i2c, 8), 0x51,
64 * KiB, rainier_bmc_fruid, rainier_bmc_fruid_len);
create_pca9552(soc, 8, 0x60);
create_pca9552(soc, 8, 0x61);
/* Bus 8: ucd90320@11 */
/* Bus 8: ucd90320@b */
/* Bus 8: ucd90320@c */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 9), "tmp423", 0x4c);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 9), "tmp423", 0x4d);
at24c_eeprom_init(aspeed_i2c_get_bus(&soc->i2c, 9), 0x50, 128 * KiB);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 10), "tmp423", 0x4c);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 10), "tmp423", 0x4d);
at24c_eeprom_init(aspeed_i2c_get_bus(&soc->i2c, 10), 0x50, 128 * KiB);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 11), TYPE_TMP105,
0x48);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 11), TYPE_TMP105,
0x49);
i2c_mux = i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 11),
"pca9546", 0x70);
at24c_eeprom_init(pca954x_i2c_get_bus(i2c_mux, 0), 0x50, 64 * KiB);
at24c_eeprom_init(pca954x_i2c_get_bus(i2c_mux, 1), 0x51, 64 * KiB);
create_pca9552(soc, 11, 0x60);
at24c_eeprom_init(aspeed_i2c_get_bus(&soc->i2c, 13), 0x50, 64 * KiB);
create_pca9552(soc, 13, 0x60);
at24c_eeprom_init(aspeed_i2c_get_bus(&soc->i2c, 14), 0x50, 64 * KiB);
create_pca9552(soc, 14, 0x60);
at24c_eeprom_init(aspeed_i2c_get_bus(&soc->i2c, 15), 0x50, 64 * KiB);
create_pca9552(soc, 15, 0x60);
}
static void get_pca9548_channels(I2CBus *bus, uint8_t mux_addr,
I2CBus **channels)
{
I2CSlave *mux = i2c_slave_create_simple(bus, "pca9548", mux_addr);
for (int i = 0; i < 8; i++) {
channels[i] = pca954x_i2c_get_bus(mux, i);
}
}
#define TYPE_LM75 TYPE_TMP105
#define TYPE_TMP75 TYPE_TMP105
#define TYPE_TMP422 "tmp422"
static void fuji_bmc_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
I2CBus *i2c[144] = {};
for (int i = 0; i < 16; i++) {
i2c[i] = aspeed_i2c_get_bus(&soc->i2c, i);
}
I2CBus *i2c180 = i2c[2];
I2CBus *i2c480 = i2c[8];
I2CBus *i2c600 = i2c[11];
get_pca9548_channels(i2c180, 0x70, &i2c[16]);
get_pca9548_channels(i2c480, 0x70, &i2c[24]);
/* NOTE: The device tree skips [32, 40) in the alias numbering */
get_pca9548_channels(i2c600, 0x77, &i2c[40]);
get_pca9548_channels(i2c[24], 0x71, &i2c[48]);
get_pca9548_channels(i2c[25], 0x72, &i2c[56]);
get_pca9548_channels(i2c[26], 0x76, &i2c[64]);
get_pca9548_channels(i2c[27], 0x76, &i2c[72]);
for (int i = 0; i < 8; i++) {
get_pca9548_channels(i2c[40 + i], 0x76, &i2c[80 + i * 8]);
}
i2c_slave_create_simple(i2c[17], TYPE_LM75, 0x4c);
i2c_slave_create_simple(i2c[17], TYPE_LM75, 0x4d);
/*
* EEPROM 24c64 size is 64Kbits or 8 Kbytes
* 24c02 size is 2Kbits or 256 bytes
*/
at24c_eeprom_init(i2c[19], 0x52, 8 * KiB);
at24c_eeprom_init(i2c[20], 0x50, 256);
at24c_eeprom_init(i2c[22], 0x52, 256);
i2c_slave_create_simple(i2c[3], TYPE_LM75, 0x48);
i2c_slave_create_simple(i2c[3], TYPE_LM75, 0x49);
i2c_slave_create_simple(i2c[3], TYPE_LM75, 0x4a);
i2c_slave_create_simple(i2c[3], TYPE_TMP422, 0x4c);
at24c_eeprom_init(i2c[8], 0x51, 8 * KiB);
i2c_slave_create_simple(i2c[8], TYPE_LM75, 0x4a);
i2c_slave_create_simple(i2c[50], TYPE_LM75, 0x4c);
at24c_eeprom_init(i2c[50], 0x52, 8 * KiB);
i2c_slave_create_simple(i2c[51], TYPE_TMP75, 0x48);
i2c_slave_create_simple(i2c[52], TYPE_TMP75, 0x49);
i2c_slave_create_simple(i2c[59], TYPE_TMP75, 0x48);
i2c_slave_create_simple(i2c[60], TYPE_TMP75, 0x49);
at24c_eeprom_init(i2c[65], 0x53, 8 * KiB);
i2c_slave_create_simple(i2c[66], TYPE_TMP75, 0x49);
i2c_slave_create_simple(i2c[66], TYPE_TMP75, 0x48);
at24c_eeprom_init(i2c[68], 0x52, 8 * KiB);
at24c_eeprom_init(i2c[69], 0x52, 8 * KiB);
at24c_eeprom_init(i2c[70], 0x52, 8 * KiB);
at24c_eeprom_init(i2c[71], 0x52, 8 * KiB);
at24c_eeprom_init(i2c[73], 0x53, 8 * KiB);
i2c_slave_create_simple(i2c[74], TYPE_TMP75, 0x49);
i2c_slave_create_simple(i2c[74], TYPE_TMP75, 0x48);
at24c_eeprom_init(i2c[76], 0x52, 8 * KiB);
at24c_eeprom_init(i2c[77], 0x52, 8 * KiB);
at24c_eeprom_init(i2c[78], 0x52, 8 * KiB);
at24c_eeprom_init(i2c[79], 0x52, 8 * KiB);
at24c_eeprom_init(i2c[28], 0x50, 256);
for (int i = 0; i < 8; i++) {
at24c_eeprom_init(i2c[81 + i * 8], 0x56, 64 * KiB);
i2c_slave_create_simple(i2c[82 + i * 8], TYPE_TMP75, 0x48);
i2c_slave_create_simple(i2c[83 + i * 8], TYPE_TMP75, 0x4b);
i2c_slave_create_simple(i2c[84 + i * 8], TYPE_TMP75, 0x4a);
}
}
#define TYPE_TMP421 "tmp421"
static void bletchley_bmc_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
I2CBus *i2c[13] = {};
for (int i = 0; i < 13; i++) {
if ((i == 8) || (i == 11)) {
continue;
}
i2c[i] = aspeed_i2c_get_bus(&soc->i2c, i);
}
/* Bus 0 - 5 all have the same config. */
for (int i = 0; i < 6; i++) {
/* Missing model: ti,ina230 @ 0x45 */
/* Missing model: mps,mp5023 @ 0x40 */
i2c_slave_create_simple(i2c[i], TYPE_TMP421, 0x4f);
/* Missing model: nxp,pca9539 @ 0x76, but PCA9552 works enough */
i2c_slave_create_simple(i2c[i], TYPE_PCA9552, 0x76);
i2c_slave_create_simple(i2c[i], TYPE_PCA9552, 0x67);
/* Missing model: fsc,fusb302 @ 0x22 */
}
/* Bus 6 */
at24c_eeprom_init(i2c[6], 0x56, 65536);
/* Missing model: nxp,pcf85263 @ 0x51 , but ds1338 works enough */
i2c_slave_create_simple(i2c[6], "ds1338", 0x51);
/* Bus 7 */
at24c_eeprom_init(i2c[7], 0x54, 65536);
/* Bus 9 */
i2c_slave_create_simple(i2c[9], TYPE_TMP421, 0x4f);
/* Bus 10 */
i2c_slave_create_simple(i2c[10], TYPE_TMP421, 0x4f);
/* Missing model: ti,hdc1080 @ 0x40 */
i2c_slave_create_simple(i2c[10], TYPE_PCA9552, 0x67);
/* Bus 12 */
/* Missing model: adi,adm1278 @ 0x11 */
i2c_slave_create_simple(i2c[12], TYPE_TMP421, 0x4c);
i2c_slave_create_simple(i2c[12], TYPE_TMP421, 0x4d);
i2c_slave_create_simple(i2c[12], TYPE_PCA9552, 0x67);
}
static void fby35_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
I2CBus *i2c[16];
for (int i = 0; i < 16; i++) {
i2c[i] = aspeed_i2c_get_bus(&soc->i2c, i);
}
i2c_slave_create_simple(i2c[2], TYPE_LM75, 0x4f);
i2c_slave_create_simple(i2c[8], TYPE_TMP421, 0x1f);
/* Hotswap controller is actually supposed to be mp5920 or ltc4282. */
i2c_slave_create_simple(i2c[11], "adm1272", 0x44);
i2c_slave_create_simple(i2c[12], TYPE_LM75, 0x4e);
i2c_slave_create_simple(i2c[12], TYPE_LM75, 0x4f);
at24c_eeprom_init(i2c[4], 0x51, 128 * KiB);
at24c_eeprom_init(i2c[6], 0x51, 128 * KiB);
at24c_eeprom_init_rom(i2c[8], 0x50, 32 * KiB, fby35_nic_fruid,
fby35_nic_fruid_len);
at24c_eeprom_init_rom(i2c[11], 0x51, 128 * KiB, fby35_bb_fruid,
fby35_bb_fruid_len);
at24c_eeprom_init_rom(i2c[11], 0x54, 128 * KiB, fby35_bmc_fruid,
fby35_bmc_fruid_len);
/*
* TODO: There is a multi-master i2c connection to an AST1030 MiniBMC on
* buses 0, 1, 2, 3, and 9. Source address 0x10, target address 0x20 on
* each.
*/
}
static void qcom_dc_scm_bmc_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 15), "tmp105", 0x4d);
}
static void qcom_dc_scm_firework_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
I2CSlave *therm_mux, *cpuvr_mux;
/* Create the generic DC-SCM hardware */
qcom_dc_scm_bmc_i2c_init(bmc);
/* Now create the Firework specific hardware */
/* I2C7 CPUVR MUX */
cpuvr_mux = i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 7),
"pca9546", 0x70);
i2c_slave_create_simple(pca954x_i2c_get_bus(cpuvr_mux, 0), "pca9548", 0x72);
i2c_slave_create_simple(pca954x_i2c_get_bus(cpuvr_mux, 1), "pca9548", 0x72);
i2c_slave_create_simple(pca954x_i2c_get_bus(cpuvr_mux, 2), "pca9548", 0x72);
i2c_slave_create_simple(pca954x_i2c_get_bus(cpuvr_mux, 3), "pca9548", 0x72);
/* I2C8 Thermal Diodes*/
therm_mux = i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 8),
"pca9548", 0x70);
i2c_slave_create_simple(pca954x_i2c_get_bus(therm_mux, 0), TYPE_LM75, 0x4C);
i2c_slave_create_simple(pca954x_i2c_get_bus(therm_mux, 1), TYPE_LM75, 0x4C);
i2c_slave_create_simple(pca954x_i2c_get_bus(therm_mux, 2), TYPE_LM75, 0x48);
i2c_slave_create_simple(pca954x_i2c_get_bus(therm_mux, 3), TYPE_LM75, 0x48);
i2c_slave_create_simple(pca954x_i2c_get_bus(therm_mux, 4), TYPE_LM75, 0x48);
/* I2C9 Fan Controller (MAX31785) */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 9), "max31785", 0x52);
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 9), "max31785", 0x54);
}
static bool aspeed_get_mmio_exec(Object *obj, Error **errp)
{
return ASPEED_MACHINE(obj)->mmio_exec;
}
static void aspeed_set_mmio_exec(Object *obj, bool value, Error **errp)
{
ASPEED_MACHINE(obj)->mmio_exec = value;
}
static void aspeed_machine_instance_init(Object *obj)
{
ASPEED_MACHINE(obj)->mmio_exec = false;
}
static char *aspeed_get_fmc_model(Object *obj, Error **errp)
{
AspeedMachineState *bmc = ASPEED_MACHINE(obj);
return g_strdup(bmc->fmc_model);
}
static void aspeed_set_fmc_model(Object *obj, const char *value, Error **errp)
{
AspeedMachineState *bmc = ASPEED_MACHINE(obj);
g_free(bmc->fmc_model);
bmc->fmc_model = g_strdup(value);
}
static char *aspeed_get_spi_model(Object *obj, Error **errp)
{
AspeedMachineState *bmc = ASPEED_MACHINE(obj);
return g_strdup(bmc->spi_model);
}
static void aspeed_set_spi_model(Object *obj, const char *value, Error **errp)
{
AspeedMachineState *bmc = ASPEED_MACHINE(obj);
g_free(bmc->spi_model);
bmc->spi_model = g_strdup(value);
}
static char *aspeed_get_bmc_console(Object *obj, Error **errp)
{
AspeedMachineState *bmc = ASPEED_MACHINE(obj);
AspeedMachineClass *amc = ASPEED_MACHINE_GET_CLASS(bmc);
int uart_chosen = bmc->uart_chosen ? bmc->uart_chosen : amc->uart_default;
return g_strdup_printf("uart%d", aspeed_uart_index(uart_chosen));
}
static void aspeed_set_bmc_console(Object *obj, const char *value, Error **errp)
{
AspeedMachineState *bmc = ASPEED_MACHINE(obj);
AspeedMachineClass *amc = ASPEED_MACHINE_GET_CLASS(bmc);
AspeedSoCClass *sc = ASPEED_SOC_CLASS(object_class_by_name(amc->soc_name));
int val;
int uart_first = aspeed_uart_first(sc);
int uart_last = aspeed_uart_last(sc);
if (sscanf(value, "uart%u", &val) != 1) {
error_setg(errp, "Bad value for \"uart\" property");
return;
}
/* The number of UART depends on the SoC */
if (val < uart_first || val > uart_last) {
error_setg(errp, "\"uart\" should be in range [%d - %d]",
uart_first, uart_last);
return;
}
bmc->uart_chosen = val + ASPEED_DEV_UART0;
}
static void aspeed_machine_class_props_init(ObjectClass *oc)
{
object_class_property_add_bool(oc, "execute-in-place",
aspeed_get_mmio_exec,
aspeed_set_mmio_exec);
object_class_property_set_description(oc, "execute-in-place",
"boot directly from CE0 flash device");
object_class_property_add_str(oc, "bmc-console", aspeed_get_bmc_console,
aspeed_set_bmc_console);
object_class_property_set_description(oc, "bmc-console",
"Change the default UART to \"uartX\"");
object_class_property_add_str(oc, "fmc-model", aspeed_get_fmc_model,
aspeed_set_fmc_model);
object_class_property_set_description(oc, "fmc-model",
"Change the FMC Flash model");
object_class_property_add_str(oc, "spi-model", aspeed_get_spi_model,
aspeed_set_spi_model);
object_class_property_set_description(oc, "spi-model",
"Change the SPI Flash model");
}
static void aspeed_machine_class_init_cpus_defaults(MachineClass *mc)
{
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(mc);
AspeedSoCClass *sc = ASPEED_SOC_CLASS(object_class_by_name(amc->soc_name));
mc->default_cpus = sc->num_cpus;
mc->min_cpus = sc->num_cpus;
mc->max_cpus = sc->num_cpus;
mc->valid_cpu_types = sc->valid_cpu_types;
}
static void aspeed_machine_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->init = aspeed_machine_init;
mc->no_floppy = 1;
mc->no_cdrom = 1;
mc->no_parallel = 1;
mc->default_ram_id = "ram";
amc->macs_mask = ASPEED_MAC0_ON;
amc->uart_default = ASPEED_DEV_UART5;
aspeed_machine_class_props_init(oc);
}
static void aspeed_machine_palmetto_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "OpenPOWER Palmetto BMC (ARM926EJ-S)";
amc->soc_name = "ast2400-a1";
amc->hw_strap1 = PALMETTO_BMC_HW_STRAP1;
amc->fmc_model = "n25q256a";
amc->spi_model = "mx25l25635f";
amc->num_cs = 1;
amc->i2c_init = palmetto_bmc_i2c_init;
mc->default_ram_size = 256 * MiB;
aspeed_machine_class_init_cpus_defaults(mc);
};
static void aspeed_machine_quanta_q71l_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Quanta-Q71l BMC (ARM926EJ-S)";
amc->soc_name = "ast2400-a1";
amc->hw_strap1 = QUANTA_Q71L_BMC_HW_STRAP1;
amc->fmc_model = "n25q256a";
amc->spi_model = "mx25l25635e";
amc->num_cs = 1;
amc->i2c_init = quanta_q71l_bmc_i2c_init;
mc->default_ram_size = 128 * MiB;
aspeed_machine_class_init_cpus_defaults(mc);
}
static void aspeed_machine_supermicrox11_bmc_class_init(ObjectClass *oc,
void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Supermicro X11 BMC (ARM926EJ-S)";
amc->soc_name = "ast2400-a1";
amc->hw_strap1 = SUPERMICROX11_BMC_HW_STRAP1;
amc->fmc_model = "mx25l25635e";
amc->spi_model = "mx25l25635e";
amc->num_cs = 1;
amc->macs_mask = ASPEED_MAC0_ON | ASPEED_MAC1_ON;
amc->i2c_init = palmetto_bmc_i2c_init;
mc->default_ram_size = 256 * MiB;
aspeed_machine_class_init_cpus_defaults(mc);
}
static void aspeed_machine_supermicro_x11spi_bmc_class_init(ObjectClass *oc,
void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Supermicro X11 SPI BMC (ARM1176)";
amc->soc_name = "ast2500-a1";
amc->hw_strap1 = SUPERMICRO_X11SPI_BMC_HW_STRAP1;
amc->fmc_model = "mx25l25635e";
amc->spi_model = "mx25l25635e";
amc->num_cs = 1;
amc->macs_mask = ASPEED_MAC0_ON | ASPEED_MAC1_ON;
amc->i2c_init = palmetto_bmc_i2c_init;
mc->default_ram_size = 512 * MiB;
aspeed_machine_class_init_cpus_defaults(mc);
}
static void aspeed_machine_ast2500_evb_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Aspeed AST2500 EVB (ARM1176)";
amc->soc_name = "ast2500-a1";
amc->hw_strap1 = AST2500_EVB_HW_STRAP1;
amc->fmc_model = "mx25l25635e";
amc->spi_model = "mx25l25635f";
amc->num_cs = 1;
amc->i2c_init = ast2500_evb_i2c_init;
mc->default_ram_size = 512 * MiB;
aspeed_machine_class_init_cpus_defaults(mc);
};
static void aspeed_machine_yosemitev2_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Facebook YosemiteV2 BMC (ARM1176)";
amc->soc_name = "ast2500-a1";
amc->hw_strap1 = AST2500_EVB_HW_STRAP1;
amc->hw_strap2 = 0;
amc->fmc_model = "n25q256a";
amc->spi_model = "mx25l25635e";
amc->num_cs = 2;
amc->i2c_init = yosemitev2_bmc_i2c_init;
mc->default_ram_size = 512 * MiB;
aspeed_machine_class_init_cpus_defaults(mc);
};
static void aspeed_machine_romulus_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "OpenPOWER Romulus BMC (ARM1176)";
amc->soc_name = "ast2500-a1";
amc->hw_strap1 = ROMULUS_BMC_HW_STRAP1;
amc->fmc_model = "n25q256a";
amc->spi_model = "mx66l1g45g";
amc->num_cs = 2;
amc->i2c_init = romulus_bmc_i2c_init;
mc->default_ram_size = 512 * MiB;
aspeed_machine_class_init_cpus_defaults(mc);
};
static void aspeed_machine_tiogapass_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Facebook Tiogapass BMC (ARM1176)";
amc->soc_name = "ast2500-a1";
amc->hw_strap1 = AST2500_EVB_HW_STRAP1;
amc->hw_strap2 = 0;
amc->fmc_model = "n25q256a";
amc->spi_model = "mx25l25635e";
amc->num_cs = 2;
amc->i2c_init = tiogapass_bmc_i2c_init;
mc->default_ram_size = 1 * GiB;
aspeed_machine_class_init_cpus_defaults(mc);
};
static void aspeed_machine_sonorapass_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "OCP SonoraPass BMC (ARM1176)";
amc->soc_name = "ast2500-a1";
amc->hw_strap1 = SONORAPASS_BMC_HW_STRAP1;
amc->fmc_model = "mx66l1g45g";
amc->spi_model = "mx66l1g45g";
amc->num_cs = 2;
amc->i2c_init = sonorapass_bmc_i2c_init;
mc->default_ram_size = 512 * MiB;
aspeed_machine_class_init_cpus_defaults(mc);
};
static void aspeed_machine_witherspoon_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "OpenPOWER Witherspoon BMC (ARM1176)";
amc->soc_name = "ast2500-a1";
amc->hw_strap1 = WITHERSPOON_BMC_HW_STRAP1;
amc->fmc_model = "mx25l25635f";
amc->spi_model = "mx66l1g45g";
amc->num_cs = 2;
amc->i2c_init = witherspoon_bmc_i2c_init;
mc->default_ram_size = 512 * MiB;
aspeed_machine_class_init_cpus_defaults(mc);
};
static void aspeed_machine_ast2600_evb_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Aspeed AST2600 EVB (Cortex-A7)";
amc->soc_name = "ast2600-a3";
amc->hw_strap1 = AST2600_EVB_HW_STRAP1;
amc->hw_strap2 = AST2600_EVB_HW_STRAP2;
amc->fmc_model = "mx66u51235f";
amc->spi_model = "mx66u51235f";
amc->num_cs = 1;
amc->macs_mask = ASPEED_MAC0_ON | ASPEED_MAC1_ON | ASPEED_MAC2_ON |
ASPEED_MAC3_ON;
amc->i2c_init = ast2600_evb_i2c_init;
mc->default_ram_size = 1 * GiB;
aspeed_machine_class_init_cpus_defaults(mc);
};
static void aspeed_machine_tacoma_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "OpenPOWER Tacoma BMC (Cortex-A7)";
amc->soc_name = "ast2600-a3";
amc->hw_strap1 = TACOMA_BMC_HW_STRAP1;
amc->hw_strap2 = TACOMA_BMC_HW_STRAP2;
amc->fmc_model = "mx66l1g45g";
amc->spi_model = "mx66l1g45g";
amc->num_cs = 2;
amc->macs_mask = ASPEED_MAC2_ON;
amc->i2c_init = witherspoon_bmc_i2c_init; /* Same board layout */
mc->default_ram_size = 1 * GiB;
aspeed_machine_class_init_cpus_defaults(mc);
};
static void aspeed_machine_g220a_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Bytedance G220A BMC (ARM1176)";
amc->soc_name = "ast2500-a1";
amc->hw_strap1 = G220A_BMC_HW_STRAP1;
amc->fmc_model = "n25q512a";
amc->spi_model = "mx25l25635e";
amc->num_cs = 2;
amc->macs_mask = ASPEED_MAC0_ON | ASPEED_MAC1_ON;
amc->i2c_init = g220a_bmc_i2c_init;
mc->default_ram_size = 1024 * MiB;
aspeed_machine_class_init_cpus_defaults(mc);
};
static void aspeed_machine_fp5280g2_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Inspur FP5280G2 BMC (ARM1176)";
amc->soc_name = "ast2500-a1";
amc->hw_strap1 = FP5280G2_BMC_HW_STRAP1;
amc->fmc_model = "n25q512a";
amc->spi_model = "mx25l25635e";
amc->num_cs = 2;
amc->macs_mask = ASPEED_MAC0_ON | ASPEED_MAC1_ON;
amc->i2c_init = fp5280g2_bmc_i2c_init;
mc->default_ram_size = 512 * MiB;
aspeed_machine_class_init_cpus_defaults(mc);
};
static void aspeed_machine_rainier_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "IBM Rainier BMC (Cortex-A7)";
amc->soc_name = "ast2600-a3";
amc->hw_strap1 = RAINIER_BMC_HW_STRAP1;
amc->hw_strap2 = RAINIER_BMC_HW_STRAP2;
amc->fmc_model = "mx66l1g45g";
amc->spi_model = "mx66l1g45g";
amc->num_cs = 2;
amc->macs_mask = ASPEED_MAC2_ON | ASPEED_MAC3_ON;
amc->i2c_init = rainier_bmc_i2c_init;
mc->default_ram_size = 1 * GiB;
aspeed_machine_class_init_cpus_defaults(mc);
};
#define FUJI_BMC_RAM_SIZE ASPEED_RAM_SIZE(2 * GiB)
static void aspeed_machine_fuji_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Facebook Fuji BMC (Cortex-A7)";
amc->soc_name = "ast2600-a3";
amc->hw_strap1 = FUJI_BMC_HW_STRAP1;
amc->hw_strap2 = FUJI_BMC_HW_STRAP2;
amc->fmc_model = "mx66l1g45g";
amc->spi_model = "mx66l1g45g";
amc->num_cs = 2;
amc->macs_mask = ASPEED_MAC3_ON;
amc->i2c_init = fuji_bmc_i2c_init;
amc->uart_default = ASPEED_DEV_UART1;
mc->default_ram_size = FUJI_BMC_RAM_SIZE;
aspeed_machine_class_init_cpus_defaults(mc);
};
#define BLETCHLEY_BMC_RAM_SIZE ASPEED_RAM_SIZE(2 * GiB)
static void aspeed_machine_bletchley_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Facebook Bletchley BMC (Cortex-A7)";
amc->soc_name = "ast2600-a3";
amc->hw_strap1 = BLETCHLEY_BMC_HW_STRAP1;
amc->hw_strap2 = BLETCHLEY_BMC_HW_STRAP2;
amc->fmc_model = "w25q01jvq";
amc->spi_model = NULL;
amc->num_cs = 2;
amc->macs_mask = ASPEED_MAC2_ON;
amc->i2c_init = bletchley_bmc_i2c_init;
mc->default_ram_size = BLETCHLEY_BMC_RAM_SIZE;
aspeed_machine_class_init_cpus_defaults(mc);
}
static void fby35_reset(MachineState *state, ShutdownCause reason)
{
AspeedMachineState *bmc = ASPEED_MACHINE(state);
AspeedGPIOState *gpio = &bmc->soc->gpio;
qemu_devices_reset(reason);
/* Board ID: 7 (Class-1, 4 slots) */
object_property_set_bool(OBJECT(gpio), "gpioV4", true, &error_fatal);
object_property_set_bool(OBJECT(gpio), "gpioV5", true, &error_fatal);
object_property_set_bool(OBJECT(gpio), "gpioV6", true, &error_fatal);
object_property_set_bool(OBJECT(gpio), "gpioV7", false, &error_fatal);
/* Slot presence pins, inverse polarity. (False means present) */
object_property_set_bool(OBJECT(gpio), "gpioH4", false, &error_fatal);
object_property_set_bool(OBJECT(gpio), "gpioH5", true, &error_fatal);
object_property_set_bool(OBJECT(gpio), "gpioH6", true, &error_fatal);
object_property_set_bool(OBJECT(gpio), "gpioH7", true, &error_fatal);
/* Slot 12v power pins, normal polarity. (True means powered-on) */
object_property_set_bool(OBJECT(gpio), "gpioB2", true, &error_fatal);
object_property_set_bool(OBJECT(gpio), "gpioB3", false, &error_fatal);
object_property_set_bool(OBJECT(gpio), "gpioB4", false, &error_fatal);
object_property_set_bool(OBJECT(gpio), "gpioB5", false, &error_fatal);
}
static void aspeed_machine_fby35_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Facebook fby35 BMC (Cortex-A7)";
mc->reset = fby35_reset;
amc->fmc_model = "mx66l1g45g";
amc->num_cs = 2;
amc->macs_mask = ASPEED_MAC3_ON;
amc->i2c_init = fby35_i2c_init;
/* FIXME: Replace this macro with something more general */
mc->default_ram_size = FUJI_BMC_RAM_SIZE;
aspeed_machine_class_init_cpus_defaults(mc);
}
#define AST1030_INTERNAL_FLASH_SIZE (1024 * 1024)
/* Main SYSCLK frequency in Hz (200MHz) */
#define SYSCLK_FRQ 200000000ULL
static void aspeed_minibmc_machine_init(MachineState *machine)
{
AspeedMachineState *bmc = ASPEED_MACHINE(machine);
AspeedMachineClass *amc = ASPEED_MACHINE_GET_CLASS(machine);
Clock *sysclk;
sysclk = clock_new(OBJECT(machine), "SYSCLK");
clock_set_hz(sysclk, SYSCLK_FRQ);
bmc->soc = ASPEED_SOC(object_new(amc->soc_name));
object_property_add_child(OBJECT(machine), "soc", OBJECT(bmc->soc));
object_unref(OBJECT(bmc->soc));
qdev_connect_clock_in(DEVICE(bmc->soc), "sysclk", sysclk);
object_property_set_link(OBJECT(bmc->soc), "memory",
OBJECT(get_system_memory()), &error_abort);
connect_serial_hds_to_uarts(bmc);
qdev_realize(DEVICE(bmc->soc), NULL, &error_abort);
aspeed_board_init_flashes(&bmc->soc->fmc,
bmc->fmc_model ? bmc->fmc_model : amc->fmc_model,
amc->num_cs,
0);
aspeed_board_init_flashes(&bmc->soc->spi[0],
bmc->spi_model ? bmc->spi_model : amc->spi_model,
amc->num_cs, amc->num_cs);
aspeed_board_init_flashes(&bmc->soc->spi[1],
bmc->spi_model ? bmc->spi_model : amc->spi_model,
amc->num_cs, (amc->num_cs * 2));
if (amc->i2c_init) {
amc->i2c_init(bmc);
}
armv7m_load_kernel(ARM_CPU(first_cpu),
machine->kernel_filename,
0,
AST1030_INTERNAL_FLASH_SIZE);
}
static void ast1030_evb_i2c_init(AspeedMachineState *bmc)
{
AspeedSoCState *soc = bmc->soc;
/* U10 24C08 connects to SDA/SCL Group 1 by default */
uint8_t *eeprom_buf = g_malloc0(32 * 1024);
smbus_eeprom_init_one(aspeed_i2c_get_bus(&soc->i2c, 0), 0x50, eeprom_buf);
/* U11 LM75 connects to SDA/SCL Group 2 by default */
i2c_slave_create_simple(aspeed_i2c_get_bus(&soc->i2c, 1), "tmp105", 0x4d);
}
static void aspeed_minibmc_machine_ast1030_evb_class_init(ObjectClass *oc,
void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Aspeed AST1030 MiniBMC (Cortex-M4)";
amc->soc_name = "ast1030-a1";
amc->hw_strap1 = 0;
amc->hw_strap2 = 0;
mc->init = aspeed_minibmc_machine_init;
amc->i2c_init = ast1030_evb_i2c_init;
mc->default_ram_size = 0;
amc->fmc_model = "sst25vf032b";
amc->spi_model = "sst25vf032b";
amc->num_cs = 2;
amc->macs_mask = 0;
aspeed_machine_class_init_cpus_defaults(mc);
}
#ifdef TARGET_AARCH64
static void aspeed_machine_ast2700_evb_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Aspeed AST2700 EVB (Cortex-A35)";
amc->soc_name = "ast2700-a0";
amc->hw_strap1 = AST2700_EVB_HW_STRAP1;
amc->hw_strap2 = AST2700_EVB_HW_STRAP2;
amc->fmc_model = "w25q01jvq";
amc->spi_model = "w25q512jv";
amc->num_cs = 2;
amc->macs_mask = ASPEED_MAC0_ON | ASPEED_MAC1_ON | ASPEED_MAC2_ON;
amc->uart_default = ASPEED_DEV_UART12;
mc->default_ram_size = 1 * GiB;
aspeed_machine_class_init_cpus_defaults(mc);
}
#endif
static void aspeed_machine_qcom_dc_scm_v1_class_init(ObjectClass *oc,
void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Qualcomm DC-SCM V1 BMC (Cortex A7)";
amc->soc_name = "ast2600-a3";
amc->hw_strap1 = QCOM_DC_SCM_V1_BMC_HW_STRAP1;
amc->hw_strap2 = QCOM_DC_SCM_V1_BMC_HW_STRAP2;
amc->fmc_model = "n25q512a";
amc->spi_model = "n25q512a";
amc->num_cs = 2;
amc->macs_mask = ASPEED_MAC2_ON | ASPEED_MAC3_ON;
amc->i2c_init = qcom_dc_scm_bmc_i2c_init;
mc->default_ram_size = 1 * GiB;
aspeed_machine_class_init_cpus_defaults(mc);
};
static void aspeed_machine_qcom_firework_class_init(ObjectClass *oc,
void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
AspeedMachineClass *amc = ASPEED_MACHINE_CLASS(oc);
mc->desc = "Qualcomm DC-SCM V1/Firework BMC (Cortex A7)";
amc->soc_name = "ast2600-a3";
amc->hw_strap1 = QCOM_DC_SCM_V1_BMC_HW_STRAP1;
amc->hw_strap2 = QCOM_DC_SCM_V1_BMC_HW_STRAP2;
amc->fmc_model = "n25q512a";
amc->spi_model = "n25q512a";
amc->num_cs = 2;
amc->macs_mask = ASPEED_MAC2_ON | ASPEED_MAC3_ON;
amc->i2c_init = qcom_dc_scm_firework_i2c_init;
mc->default_ram_size = 1 * GiB;
aspeed_machine_class_init_cpus_defaults(mc);
};
static const TypeInfo aspeed_machine_types[] = {
{
.name = MACHINE_TYPE_NAME("palmetto-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_palmetto_class_init,
}, {
.name = MACHINE_TYPE_NAME("supermicrox11-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_supermicrox11_bmc_class_init,
}, {
.name = MACHINE_TYPE_NAME("supermicro-x11spi-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_supermicro_x11spi_bmc_class_init,
}, {
.name = MACHINE_TYPE_NAME("ast2500-evb"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_ast2500_evb_class_init,
}, {
.name = MACHINE_TYPE_NAME("romulus-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_romulus_class_init,
}, {
.name = MACHINE_TYPE_NAME("sonorapass-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_sonorapass_class_init,
}, {
.name = MACHINE_TYPE_NAME("witherspoon-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_witherspoon_class_init,
}, {
.name = MACHINE_TYPE_NAME("ast2600-evb"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_ast2600_evb_class_init,
}, {
.name = MACHINE_TYPE_NAME("yosemitev2-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_yosemitev2_class_init,
}, {
.name = MACHINE_TYPE_NAME("tacoma-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_tacoma_class_init,
}, {
.name = MACHINE_TYPE_NAME("tiogapass-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_tiogapass_class_init,
}, {
.name = MACHINE_TYPE_NAME("g220a-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_g220a_class_init,
}, {
.name = MACHINE_TYPE_NAME("qcom-dc-scm-v1-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_qcom_dc_scm_v1_class_init,
}, {
.name = MACHINE_TYPE_NAME("qcom-firework-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_qcom_firework_class_init,
}, {
.name = MACHINE_TYPE_NAME("fp5280g2-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_fp5280g2_class_init,
}, {
.name = MACHINE_TYPE_NAME("quanta-q71l-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_quanta_q71l_class_init,
}, {
.name = MACHINE_TYPE_NAME("rainier-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_rainier_class_init,
}, {
.name = MACHINE_TYPE_NAME("fuji-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_fuji_class_init,
}, {
.name = MACHINE_TYPE_NAME("bletchley-bmc"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_bletchley_class_init,
}, {
.name = MACHINE_TYPE_NAME("fby35-bmc"),
.parent = MACHINE_TYPE_NAME("ast2600-evb"),
.class_init = aspeed_machine_fby35_class_init,
}, {
.name = MACHINE_TYPE_NAME("ast1030-evb"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_minibmc_machine_ast1030_evb_class_init,
#ifdef TARGET_AARCH64
}, {
.name = MACHINE_TYPE_NAME("ast2700-evb"),
.parent = TYPE_ASPEED_MACHINE,
.class_init = aspeed_machine_ast2700_evb_class_init,
#endif
}, {
.name = TYPE_ASPEED_MACHINE,
.parent = TYPE_MACHINE,
.instance_size = sizeof(AspeedMachineState),
.instance_init = aspeed_machine_instance_init,
.class_size = sizeof(AspeedMachineClass),
.class_init = aspeed_machine_class_init,
.abstract = true,
}
};
DEFINE_TYPES(aspeed_machine_types)