QCA vendor command to configure conditional switch channel for AP
This commit introduces a new vendor sub command
QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH and associated
attributes which aim to configure selected frequencies on which the AP
can conditionally switch onto for preferred operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
diff --git a/src/common/qca-vendor.h b/src/common/qca-vendor.h
index ff8cef9..afc3c2f 100644
--- a/src/common/qca-vendor.h
+++ b/src/common/qca-vendor.h
@@ -102,6 +102,19 @@
* device. As an event, it indicates either the feature stopped after it
* was already running or feature has actually failed to start. Uses the
* attributes defines in enum qca_wlan_vendor_attr_p2p_listen_offload.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After AP starts
+ * beaconing, this sub command provides the driver, the frequencies on the
+ * 5 GHz band to check for any radar activity. Driver selects one channel
+ * from this priority list provided through
+ * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts
+ * to check for radar activity on it. If no radar activity is detected
+ * during the channel availability check period, driver internally switches
+ * to the selected frequency of operation. If the frequency is zero, driver
+ * internally selects a channel. The status of this conditional switch is
+ * indicated through an event using the same sub command through
+ * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are
+ * listed in qca_wlan_vendor_attr_sap_conditional_chan_switch.
*/
enum qca_nl80211_vendor_subcmds {
QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0,
@@ -186,6 +199,7 @@
/* 121 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122,
QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123,
+ QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124,
};
@@ -661,4 +675,23 @@
QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1,
};
+/**
+ * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP
+ * conditional channel switch
+ */
+enum qca_wlan_vendor_attr_sap_conditional_chan_switch {
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0,
+ /* Priority based frequency list (an array of u32 values in host byte
+ * order) */
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1,
+ /* Status of the conditional switch (u32).
+ * 0: Success, Non-zero: Failure
+ */
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2,
+
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX =
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1,
+};
+
#endif /* QCA_VENDOR_H */
