docs/specs/fw_cfg.txt - third_party/qemu - Git at Google

 QEMU Firmware Configuration (fw_cfg) Device
 ===========================================

 = Guest-side Hardware Interface =

 This hardware interface allows the guest to retrieve various data items
 (blobs) that can influence how the firmware configures itself, or may
 contain tables to be installed for the guest OS. Examples include device
 boot order, ACPI and SMBIOS tables, virtual machine UUID, SMP and NUMA
 information, kernel/initrd images for direct (Linux) kernel booting, etc.

 == Selector (Control) Register ==

 * Write only
 * Location: platform dependent (IOport or MMIO)
 * Width: 16-bit
 * Endianness: little-endian (if IOport), or big-endian (if MMIO)

 A write to this register sets the index of a firmware configuration
 item which can subsequently be accessed via the data register.

 Setting the selector register will cause the data offset to be set
 to zero. The data offset impacts which data is accessed via the data
 register, and is explained below.

 Bit14 of the selector register indicates whether the configuration
 setting is being written. A value of 0 means the item is only being
 read, and all write access to the data port will be ignored. A value
 of 1 means the item's data can be overwritten by writes to the data
 register. In other words, configuration write mode is enabled when
 the selector value is between 0x4000-0x7fff or 0xc000-0xffff.

 NOTE: As of QEMU v2.4, writes to the fw_cfg data register are no
       longer supported, and will be ignored (treated as no-ops)!

 NOTE: As of QEMU v2.9, writes are reinstated, but only through the DMA
       interface (see below). Furthermore, writeability of any specific item is
       governed independently of Bit14 in the selector key value.

 Bit15 of the selector register indicates whether the configuration
 setting is architecture specific. A value of 0 means the item is a
 generic configuration item. A value of 1 means the item is specific
 to a particular architecture. In other words, generic configuration
 items are accessed with a selector value between 0x0000-0x7fff, and
 architecture specific configuration items are accessed with a selector
 value between 0x8000-0xffff.

 == Data Register ==

 * Read/Write (writes ignored as of QEMU v2.4, but see the DMA interface)
 * Location: platform dependent (IOport [*] or MMIO)
 * Width: 8-bit (if IOport), 8/16/32/64-bit (if MMIO)
 * Endianness: string-preserving

 [*] On platforms where the data register is exposed as an IOport, its
 port number will always be one greater than the port number of the
 selector register. In other words, the two ports overlap, and can not
 be mapped separately.

 The data register allows access to an array of bytes for each firmware
 configuration data item. The specific item is selected by writing to
 the selector register, as described above.

 Initially following a write to the selector register, the data offset
 will be set to zero. Each successful access to the data register will
 increment the data offset by the appropriate access width.

 Each firmware configuration item has a maximum length of data
 associated with the item. After the data offset has passed the
 end of this maximum data length, then any reads will return a data
 value of 0x00, and all writes will be ignored.

 An N-byte wide read of the data register will return the next available
 N bytes of the selected firmware configuration item, as a substring, in
 increasing address order, similar to memcpy().

 == Register Locations ==

 === x86, x86_64 Register Locations ===

 Selector Register IOport: 0x510
 Data Register IOport:     0x511
 DMA Address IOport:       0x514

 === Arm Register Locations ===

 Selector Register address: Base + 8 (2 bytes)
 Data Register address:     Base + 0 (8 bytes)
 DMA Address address:       Base + 16 (8 bytes)

 == ACPI Interface ==

 The fw_cfg device is defined with ACPI ID "QEMU0002". Since we expect
 ACPI tables to be passed into the guest through the fw_cfg device itself,
 the guest-side firmware can not use ACPI to find fw_cfg. However, once the
 firmware is finished setting up ACPI tables and hands control over to the
 guest kernel, the latter can use the fw_cfg ACPI node for a more accurate
 inventory of in-use IOport or MMIO regions.

 == Firmware Configuration Items ==

 === Signature (Key 0x0000, FW_CFG_SIGNATURE) ===

 The presence of the fw_cfg selector and data registers can be verified
 by selecting the "signature" item using key 0x0000 (FW_CFG_SIGNATURE),
 and reading four bytes from the data register. If the fw_cfg device is
 present, the four bytes read will contain the characters "QEMU".

 If the DMA interface is available, then reading the DMA Address
 Register returns 0x51454d5520434647 ("QEMU CFG" in big-endian format).

 === Revision / feature bitmap (Key 0x0001, FW_CFG_ID) ===

 A 32-bit little-endian unsigned int, this item is used to check for enabled
 features.
  - Bit 0: traditional interface. Always set.
  - Bit 1: DMA interface.

 === File Directory (Key 0x0019, FW_CFG_FILE_DIR) ===

 Firmware configuration items stored at selector keys 0x0020 or higher
 (FW_CFG_FILE_FIRST or higher) have an associated entry in a directory
 structure, which makes it easier for guest-side firmware to identify
 and retrieve them. The format of this file directory (from fw_cfg.h in
 the QEMU source tree) is shown here, slightly annotated for clarity:

 struct FWCfgFiles {		/* the entire file directory fw_cfg item */
     uint32_t count;		/* number of entries, in big-endian format */
     struct FWCfgFile f[];	/* array of file entries, see below */
 };

 struct FWCfgFile {		/* an individual file entry, 64 bytes total */
     uint32_t size;		/* size of referenced fw_cfg item, big-endian */
     uint16_t select;		/* selector key of fw_cfg item, big-endian */
     uint16_t reserved;
     char name[56];		/* fw_cfg item name, NUL-terminated ascii */
 };

 === All Other Data Items ===

 Please consult the QEMU source for the most up-to-date and authoritative list
 of selector keys and their respective items' purpose, format and writeability.

 === Ranges ===

 Theoretically, there may be up to 0x4000 generic firmware configuration
 items, and up to 0x4000 architecturally specific ones.

 Selector Reg.    Range Usage
 ---------------  -----------
 0x0000 - 0x3fff  Generic (0x0000 - 0x3fff, generally RO, possibly RW through
                           the DMA interface in QEMU v2.9+)
 0x4000 - 0x7fff  Generic (0x0000 - 0x3fff, RW, ignored in QEMU v2.4+)
 0x8000 - 0xbfff  Arch. Specific (0x0000 - 0x3fff, generally RO, possibly RW
                                  through the DMA interface in QEMU v2.9+)
 0xc000 - 0xffff  Arch. Specific (0x0000 - 0x3fff, RW, ignored in v2.4+)

 In practice, the number of allowed firmware configuration items depends on the
 machine type/version.

 = Guest-side DMA Interface =

 If bit 1 of the feature bitmap is set, the DMA interface is present. This does
 not replace the existing fw_cfg interface, it is an add-on. This interface
 can be used through the 64-bit wide address register.

 The address register is in big-endian format. The value for the register is 0
 at startup and after an operation. A write to the least significant half (at
 offset 4) triggers an operation. This means that operations with 32-bit
 addresses can be triggered with just one write, whereas operations with
 64-bit addresses can be triggered with one 64-bit write or two 32-bit writes,
 starting with the most significant half (at offset 0).

 In this register, the physical address of a FWCfgDmaAccess structure in RAM
 should be written. This is the format of the FWCfgDmaAccess structure:

 typedef struct FWCfgDmaAccess {
     uint32_t control;
     uint32_t length;
     uint64_t address;
 } FWCfgDmaAccess;

 The fields of the structure are in big endian mode, and the field at the lowest
 address is the "control" field.

 The "control" field has the following bits:
  - Bit 0: Error
  - Bit 1: Read
  - Bit 2: Skip
  - Bit 3: Select. The upper 16 bits are the selected index.
  - Bit 4: Write

 When an operation is triggered, if the "control" field has bit 3 set, the
 upper 16 bits are interpreted as an index of a firmware configuration item.
 This has the same effect as writing the selector register.

 If the "control" field has bit 1 set, a read operation will be performed.
 "length" bytes for the current selector and offset will be copied into the
 physical RAM address specified by the "address" field.

 If the "control" field has bit 4 set (and not bit 1), a write operation will be
 performed. "length" bytes will be copied from the physical RAM address
 specified by the "address" field to the current selector and offset. QEMU
 prevents starting or finishing the write beyond the end of the item associated
 with the current selector (i.e., the item cannot be resized). Truncated writes
 are dropped entirely. Writes to read-only items are also rejected. All of these
 write errors set bit 0 (the error bit) in the "control" field.

 If the "control" field has bit 2 set (and neither bit 1 nor bit 4), a skip
 operation will be performed. The offset for the current selector will be
 advanced "length" bytes.

 To check the result, read the "control" field:
    error bit set        ->  something went wrong.
    all bits cleared     ->  transfer finished successfully.
    otherwise            ->  transfer still in progress (doesn't happen
                             today due to implementation not being async,
                             but may in the future).

 = Externally Provided Items =

 As of v2.4, "file" fw_cfg items (i.e., items with selector keys above
 FW_CFG_FILE_FIRST, and with a corresponding entry in the fw_cfg file
 directory structure) may be inserted via the QEMU command line, using
 the following syntax:

     -fw_cfg [name=]<item_name>,file=<path>

 Or

     -fw_cfg [name=]<item_name>,string=<string>

 See QEMU man page for more documentation.

 Using item_name with plain ASCII characters only is recommended.

 Item names beginning with "opt/" are reserved for users.  QEMU will
 never create entries with such names unless explicitly ordered by the
 user.

 To avoid clashes among different users, it is strongly recommended
 that you use names beginning with opt/RFQDN/, where RFQDN is a reverse
 fully qualified domain name you control.  For instance, if SeaBIOS
 wanted to define additional names, the prefix "opt/org.seabios/" would
 be appropriate.

 For historical reasons, "opt/ovmf/" is reserved for OVMF firmware.

 Prefix "opt/org.qemu/" is reserved for QEMU itself.

 Use of names not beginning with "opt/" is potentially dangerous and
 entirely unsupported.  QEMU will warn if you try.

 All externally provided fw_cfg items are read-only to the guest.
	QEMU Firmware Configuration (fw_cfg) Device
	===========================================

	= Guest-side Hardware Interface =

	This hardware interface allows the guest to retrieve various data items
	(blobs) that can influence how the firmware configures itself, or may
	contain tables to be installed for the guest OS. Examples include device
	boot order, ACPI and SMBIOS tables, virtual machine UUID, SMP and NUMA
	information, kernel/initrd images for direct (Linux) kernel booting, etc.

	== Selector (Control) Register ==

	* Write only
	* Location: platform dependent (IOport or MMIO)
	* Width: 16-bit
	* Endianness: little-endian (if IOport), or big-endian (if MMIO)

	A write to this register sets the index of a firmware configuration
	item which can subsequently be accessed via the data register.

	Setting the selector register will cause the data offset to be set
	to zero. The data offset impacts which data is accessed via the data
	register, and is explained below.

	Bit14 of the selector register indicates whether the configuration
	setting is being written. A value of 0 means the item is only being
	read, and all write access to the data port will be ignored. A value
	of 1 means the item's data can be overwritten by writes to the data
	register. In other words, configuration write mode is enabled when
	the selector value is between 0x4000-0x7fff or 0xc000-0xffff.

	NOTE: As of QEMU v2.4, writes to the fw_cfg data register are no
	longer supported, and will be ignored (treated as no-ops)!

	NOTE: As of QEMU v2.9, writes are reinstated, but only through the DMA
	interface (see below). Furthermore, writeability of any specific item is
	governed independently of Bit14 in the selector key value.

	Bit15 of the selector register indicates whether the configuration
	setting is architecture specific. A value of 0 means the item is a
	generic configuration item. A value of 1 means the item is specific
	to a particular architecture. In other words, generic configuration
	items are accessed with a selector value between 0x0000-0x7fff, and
	architecture specific configuration items are accessed with a selector
	value between 0x8000-0xffff.

	== Data Register ==

	* Read/Write (writes ignored as of QEMU v2.4, but see the DMA interface)
	* Location: platform dependent (IOport [*] or MMIO)
	* Width: 8-bit (if IOport), 8/16/32/64-bit (if MMIO)
	* Endianness: string-preserving

	[*] On platforms where the data register is exposed as an IOport, its
	port number will always be one greater than the port number of the
	selector register. In other words, the two ports overlap, and can not
	be mapped separately.

	The data register allows access to an array of bytes for each firmware
	configuration data item. The specific item is selected by writing to
	the selector register, as described above.

	Initially following a write to the selector register, the data offset
	will be set to zero. Each successful access to the data register will
	increment the data offset by the appropriate access width.

	Each firmware configuration item has a maximum length of data
	associated with the item. After the data offset has passed the
	end of this maximum data length, then any reads will return a data
	value of 0x00, and all writes will be ignored.

	An N-byte wide read of the data register will return the next available
	N bytes of the selected firmware configuration item, as a substring, in
	increasing address order, similar to memcpy().

	== Register Locations ==

	=== x86, x86_64 Register Locations ===

	Selector Register IOport: 0x510
	Data Register IOport: 0x511
	DMA Address IOport: 0x514

	=== Arm Register Locations ===

	Selector Register address: Base + 8 (2 bytes)
	Data Register address: Base + 0 (8 bytes)
	DMA Address address: Base + 16 (8 bytes)

	== ACPI Interface ==

	The fw_cfg device is defined with ACPI ID "QEMU0002". Since we expect
	ACPI tables to be passed into the guest through the fw_cfg device itself,
	the guest-side firmware can not use ACPI to find fw_cfg. However, once the
	firmware is finished setting up ACPI tables and hands control over to the
	guest kernel, the latter can use the fw_cfg ACPI node for a more accurate
	inventory of in-use IOport or MMIO regions.

	== Firmware Configuration Items ==

	=== Signature (Key 0x0000, FW_CFG_SIGNATURE) ===

	The presence of the fw_cfg selector and data registers can be verified
	by selecting the "signature" item using key 0x0000 (FW_CFG_SIGNATURE),
	and reading four bytes from the data register. If the fw_cfg device is
	present, the four bytes read will contain the characters "QEMU".

	If the DMA interface is available, then reading the DMA Address
	Register returns 0x51454d5520434647 ("QEMU CFG" in big-endian format).

	=== Revision / feature bitmap (Key 0x0001, FW_CFG_ID) ===

	A 32-bit little-endian unsigned int, this item is used to check for enabled
	features.
	- Bit 0: traditional interface. Always set.
	- Bit 1: DMA interface.

	=== File Directory (Key 0x0019, FW_CFG_FILE_DIR) ===

	Firmware configuration items stored at selector keys 0x0020 or higher
	(FW_CFG_FILE_FIRST or higher) have an associated entry in a directory
	structure, which makes it easier for guest-side firmware to identify
	and retrieve them. The format of this file directory (from fw_cfg.h in
	the QEMU source tree) is shown here, slightly annotated for clarity:

	struct FWCfgFiles { /* the entire file directory fw_cfg item */
	uint32_t count; /* number of entries, in big-endian format */
	struct FWCfgFile f[]; /* array of file entries, see below */
	};

	struct FWCfgFile { /* an individual file entry, 64 bytes total */
	uint32_t size; /* size of referenced fw_cfg item, big-endian */
	uint16_t select; /* selector key of fw_cfg item, big-endian */
	uint16_t reserved;
	char name[56]; /* fw_cfg item name, NUL-terminated ascii */
	};

	=== All Other Data Items ===

	Please consult the QEMU source for the most up-to-date and authoritative list
	of selector keys and their respective items' purpose, format and writeability.

	=== Ranges ===

	Theoretically, there may be up to 0x4000 generic firmware configuration
	items, and up to 0x4000 architecturally specific ones.

	Selector Reg. Range Usage
	--------------- -----------
	0x0000 - 0x3fff Generic (0x0000 - 0x3fff, generally RO, possibly RW through
	the DMA interface in QEMU v2.9+)
	0x4000 - 0x7fff Generic (0x0000 - 0x3fff, RW, ignored in QEMU v2.4+)
	0x8000 - 0xbfff Arch. Specific (0x0000 - 0x3fff, generally RO, possibly RW
	through the DMA interface in QEMU v2.9+)
	0xc000 - 0xffff Arch. Specific (0x0000 - 0x3fff, RW, ignored in v2.4+)

	In practice, the number of allowed firmware configuration items depends on the
	machine type/version.

	= Guest-side DMA Interface =

	If bit 1 of the feature bitmap is set, the DMA interface is present. This does
	not replace the existing fw_cfg interface, it is an add-on. This interface
	can be used through the 64-bit wide address register.

	The address register is in big-endian format. The value for the register is 0
	at startup and after an operation. A write to the least significant half (at
	offset 4) triggers an operation. This means that operations with 32-bit
	addresses can be triggered with just one write, whereas operations with
	64-bit addresses can be triggered with one 64-bit write or two 32-bit writes,
	starting with the most significant half (at offset 0).

	In this register, the physical address of a FWCfgDmaAccess structure in RAM
	should be written. This is the format of the FWCfgDmaAccess structure:

	typedef struct FWCfgDmaAccess {
	uint32_t control;
	uint32_t length;
	uint64_t address;
	} FWCfgDmaAccess;

	The fields of the structure are in big endian mode, and the field at the lowest
	address is the "control" field.

	The "control" field has the following bits:
	- Bit 0: Error
	- Bit 1: Read
	- Bit 2: Skip
	- Bit 3: Select. The upper 16 bits are the selected index.
	- Bit 4: Write

	When an operation is triggered, if the "control" field has bit 3 set, the
	upper 16 bits are interpreted as an index of a firmware configuration item.
	This has the same effect as writing the selector register.

	If the "control" field has bit 1 set, a read operation will be performed.
	"length" bytes for the current selector and offset will be copied into the
	physical RAM address specified by the "address" field.

	If the "control" field has bit 4 set (and not bit 1), a write operation will be
	performed. "length" bytes will be copied from the physical RAM address
	specified by the "address" field to the current selector and offset. QEMU
	prevents starting or finishing the write beyond the end of the item associated
	with the current selector (i.e., the item cannot be resized). Truncated writes
	are dropped entirely. Writes to read-only items are also rejected. All of these
	write errors set bit 0 (the error bit) in the "control" field.

	If the "control" field has bit 2 set (and neither bit 1 nor bit 4), a skip
	operation will be performed. The offset for the current selector will be
	advanced "length" bytes.

	To check the result, read the "control" field:
	error bit set -> something went wrong.
	all bits cleared -> transfer finished successfully.
	otherwise -> transfer still in progress (doesn't happen
	today due to implementation not being async,
	but may in the future).

	= Externally Provided Items =

	As of v2.4, "file" fw_cfg items (i.e., items with selector keys above
	FW_CFG_FILE_FIRST, and with a corresponding entry in the fw_cfg file
	directory structure) may be inserted via the QEMU command line, using
	the following syntax:

	-fw_cfg [name=]<item_name>,file=<path>

	Or

	-fw_cfg [name=]<item_name>,string=<string>

	See QEMU man page for more documentation.

	Using item_name with plain ASCII characters only is recommended.

	Item names beginning with "opt/" are reserved for users. QEMU will
	never create entries with such names unless explicitly ordered by the
	user.

	To avoid clashes among different users, it is strongly recommended
	that you use names beginning with opt/RFQDN/, where RFQDN is a reverse
	fully qualified domain name you control. For instance, if SeaBIOS
	wanted to define additional names, the prefix "opt/org.seabios/" would
	be appropriate.

	For historical reasons, "opt/ovmf/" is reserved for OVMF firmware.

	Prefix "opt/org.qemu/" is reserved for QEMU itself.

	Use of names not beginning with "opt/" is potentially dangerous and
	entirely unsupported. QEMU will warn if you try.

	All externally provided fw_cfg items are read-only to the guest.