/* Dropbear SSH
 * Copyright (c) 2002,2003 Matt Johnston
 * All rights reserved. See LICENSE for the license. */

#ifndef _OPTIONS_H_
#define _OPTIONS_H_

/******************************************************************
 * Define compile-time options below - the "#ifndef DROPBEAR_XXX .... #endif"
 * parts are to allow for commandline -DDROPBEAR_XXX options etc.
 ******************************************************************/

#ifndef DROPBEAR_PORT
#define DROPBEAR_PORT 22
#endif

/* Default hostkey paths - these can be specified on the command line */
#ifndef DSS_PRIV_FILENAME
#define DSS_PRIV_FILENAME "/etc/dropbear/dropbear_dss_host_key"
#endif
#ifndef RSA_PRIV_FILENAME
#define RSA_PRIV_FILENAME "/etc/dropbear/dropbear_rsa_host_key"
#endif

/* Set NON_INETD_MODE if you require daemon functionality (ie Dropbear listens
 * on chosen ports and keeps accepting connections. This is the default.
 *
 * Set INETD_MODE if you want to be able to run Dropbear with inetd (or
 * similar), where it will use stdin/stdout for connections, and each process
 * lasts for a single connection. Dropbear should be invoked with the -i flag
 * for inetd, and can only accept IPv4 connections.
 *
 * Both of these flags can be defined at once, don't compile without at least
 * one of them. */
#define NON_INETD_MODE
#define INETD_MODE

/* Setting this disables the fast exptmod bignum code. It saves ~5kB, but is
 * perhaps 20% slower for pubkey operations (it is probably worth experimenting
 * if you want to use this) */
/*#define NO_FAST_EXPTMOD*/

/* Set this if you want to use the DROPBEAR_SMALL_CODE option. This can save
several kB in binary size, however will make the symmetrical ciphers (AES, DES
etc) slower (perhaps by 50%). Recommended for most small systems. */
#define DROPBEAR_SMALL_CODE

/* Enable X11 Forwarding - server only */
#define ENABLE_X11FWD

/* Enable TCP Fowarding */
/* 'Local' is "-L" style (client listening port forwarded via server)
 * 'Remote' is "-R" style (server listening port forwarded via client) */

#define ENABLE_CLI_LOCALTCPFWD
#define ENABLE_CLI_REMOTETCPFWD

#define ENABLE_SVR_LOCALTCPFWD
#define ENABLE_SVR_REMOTETCPFWD

/* Enable Authentication Agent Forwarding - server only for now */
#define ENABLE_AGENTFWD

/* Encryption - at least one required.
 * RFC Draft requires 3DES, and recommends Blowfish, AES128 & Twofish128 */
#define DROPBEAR_AES128_CBC
#define DROPBEAR_BLOWFISH_CBC
#define DROPBEAR_TWOFISH128_CBC
#define DROPBEAR_3DES_CBC

/* Integrity - at least one required.
 * RFC Draft requires sha1-hmac, and recommends md5-hmac.
 *
 * Note: there's no point disabling sha1 to save space, since it's used in the
 * for the random number generator and public-key cryptography anyway.
 * Disabling it here will just stop it from being used as the integrity portion
 * of the ssh protocol.
 *
 * These are also used for key fingerprints in logs (when pubkey auth is used),
 * MD5 fingerprints are printed if available, however SHA1 fingerprints will be
 * generated otherwise. This isn't exactly optimal, although SHA1 fingerprints
 * are not too hard to create from pubkeys if required. */
#define DROPBEAR_SHA1_HMAC
#define DROPBEAR_MD5_HMAC

/* Hostkey/public key algorithms - at least one required, these are used
 * for hostkey as well as for verifying signatures with pubkey auth.
 * Removing either of these won't save very much space.
 * SSH2 RFC Draft requires dss, recommends rsa */
#define DROPBEAR_RSA
#define DROPBEAR_DSS

/* Define DSS_PROTOK to use PuTTY's method of generating the value k for dss,
 * rather than just from the random byte source. Undefining this will save you
 * ~4k in binary size with static uclibc, but your DSS hostkey could be exposed
 * if the random number source isn't good. In general this isn't required */
/* #define DSS_PROTOK */

/* Whether to do reverse DNS lookups. This is advisable, though will add
 * code size with gethostbyname() etc, so for very small environments where
 * you are statically linking, you might want to undefine this */
#define DO_HOST_LOOKUP

/* Whether to print the message of the day (MOTD). This doesn't add much code
 * size */
#define DO_MOTD

/* The MOTD file path */
#ifndef MOTD_FILENAME
#define MOTD_FILENAME "/etc/motd"
#endif

/* Authentication types to enable, at least one required.
   RFC Draft requires pubkey auth, and recommends password */
#define ENABLE_SVR_PASSWORD_AUTH
#define ENABLE_SVR_PUBKEY_AUTH

#define ENABLE_CLI_PASSWORD_AUTH
#define ENABLE_CLI_PUBKEY_AUTH

/* Random device to use - you must specify _one only_.
 * DEV_URANDOM is recommended on hosts with a good /dev/urandom, otherwise use
 * PRNGD and run prngd, specifying the socket. This device must be able to
 * produce a large amount of random data, so using /dev/random or Entropy
 * Gathering Daemon (egd) may result in halting, as it waits for more random
 * data */
#define DROPBEAR_DEV_URANDOM /* use /dev/urandom */

/*#undef DROPBEAR_PRNGD */ /* use prngd socket - you must manually set up prngd
							  to produce output */
#ifndef DROPBEAR_PRNGD_SOCKET
#define DROPBEAR_PRNGD_SOCKET "/var/run/dropbear-rng"
#endif

/* Specify the number of clients we will allow to be connected but
 * not yet authenticated. After this limit, connections are rejected */
#ifndef MAX_UNAUTH_CLIENTS
#define MAX_UNAUTH_CLIENTS 30
#endif

/* Maximum number of failed authentication tries (server option) */
#ifndef MAX_AUTH_TRIES
#define MAX_AUTH_TRIES 10
#endif

/* The file to store the daemon's process ID, for shutdown scripts etc */
#ifndef DROPBEAR_PIDFILE
#define DROPBEAR_PIDFILE "/var/run/dropbear.pid"
#endif

/* The command to invoke for xauth when using X11 forwarding.
 * "-q" for quiet */
#ifndef XAUTH_COMMAND
#define XAUTH_COMMAND "/usr/X11R6/bin/xauth -q"
#endif

/* if you want to enable running an sftp server (such as the one included with
 * OpenSSH), set the path below. If the path isn't defined, sftp will not
 * be enabled */
#ifndef SFTPSERVER_PATH
#define SFTPSERVER_PATH "/usr/libexec/sftp-server"
#endif

/* This is used by the scp binary when used as a client binary. If you're
 * not using the Dropbear client, you'll need to change it */
#define _PATH_SSH_PROGRAM "/usr/bin/dbclient"

/* Multi-purpose binary configuration has now moved. Look at the top
 * of the Makefile for instructions, or INSTALL */

/*******************************************************************
 * You shouldn't edit below here unless you know you need to.
 *******************************************************************/

#ifndef DROPBEAR_VERSION
#define DROPBEAR_VERSION "0.44test2"
#endif

#define LOCAL_IDENT "SSH-2.0-dropbear_" DROPBEAR_VERSION
#define PROGNAME "dropbear"

/* Spec recommends after one hour or 1 gigabyte of data. One hour
 * is a bit too verbose, so we try 8 hours */
#ifndef KEX_REKEY_TIMEOUT
#define KEX_REKEY_TIMEOUT (3600 * 8)
#endif
#ifndef KEX_REKEY_DATA
#define KEX_REKEY_DATA (1<<30) /* 2^30 == 1GB, this value must be < INT_MAX */
#endif
/* Close connections to clients which haven't authorised after AUTH_TIMEOUT */
#ifndef AUTH_TIMEOUT
#define AUTH_TIMEOUT 300 /* we choose 5 minutes */
#endif

/* Minimum key sizes for DSS and RSA */
#ifndef MIN_DSS_KEYLEN
#define MIN_DSS_KEYLEN 512
#endif
#ifndef MIN_RSA_KEYLEN
#define MIN_RSA_KEYLEN 512
#endif

#define MAX_BANNER_SIZE 2000 /* this is 25*80 chars, any more is foolish */
#define MAX_BANNER_LINES 20 /* How many lines the client will display */

#define DEV_URANDOM "/dev/urandom"

/* the number of NAME=VALUE pairs to malloc for environ, if we don't have
 * the clearenv() function */
#define ENV_SIZE 100

#define MAX_CMD_LEN 1024 /* max length of a command */
#define MAX_TERM_LEN 200 /* max length of TERM name */

#define MAX_HOST_LEN 254 /* max hostname len for tcp fwding */
#define MAX_IP_LEN 15 /* strlen("255.255.255.255") == 15 */

#define DROPBEAR_MAX_PORTS 10 /* max number of ports which can be specified,
								 ipv4 and ipv6 don't count twice */

#define _PATH_TTY "/dev/tty"

/* Timeouts in seconds */
#define SELECT_TIMEOUT 20

/* success/failure defines */
#define DROPBEAR_SUCCESS 0
#define DROPBEAR_FAILURE -1

/* various algorithm identifiers */
#define DROPBEAR_KEX_DH_GROUP1 0

#define DROPBEAR_SIGNKEY_ANY 0
#define DROPBEAR_SIGNKEY_RSA 1
#define DROPBEAR_SIGNKEY_DSS 2
#define DROPBEAR_SIGNKEY_NONE 3

#define DROPBEAR_COMP_NONE 0
#define DROPBEAR_COMP_ZLIB 1

/* Required for pubkey auth */
#if defined(ENABLE_SVR_PUBKEY_AUTH) || defined(DROPBEAR_CLIENT)
#define DROPBEAR_SIGNKEY_VERIFY
#endif

/* SHA1 is 20 bytes == 160 bits */
#define SHA1_HASH_SIZE 20
/* SHA512 is 64 bytes == 512 bits */
#define SHA512_HASH_SIZE 64
/* MD5 is 16 bytes = 128 bits */
#define MD5_HASH_SIZE 16

/* largest of MD5 and SHA1 */
#define MAX_MAC_LEN SHA1_HASH_SIZE


#define MAX_KEY_LEN 24 /* 3DES requires a 24 byte key */
#define MAX_IV_LEN 20 /* must be same as max blocksize, 
						 and >= SHA1_HASH_SIZE */
#define MAX_MAC_KEY 20

#define MAX_NAME_LEN 64 /* maximum length of a protocol name, isn't
						   explicitly specified for all protocols (just
						   for algos) but seems valid */

#define MAX_PROPOSED_ALGO 20

/* size/count limits */
#define MAX_LISTEN_ADDR 10

#define MAX_PACKET_LEN 35000
#define MIN_PACKET_LEN 16
#define MAX_PAYLOAD_LEN 32768

#define MAX_TRANS_PAYLOAD_LEN 32768
#define MAX_TRANS_PACKET_LEN (MAX_TRANS_PAYLOAD_LEN+50)

#define MAX_TRANS_WINDOW 500000000 /* 500MB is sufficient, stopping overflow */
#define MAX_TRANS_WIN_INCR 500000000 /* overflow prevention */

#define MAX_STRING_LEN 1400 /* ~= MAX_PROPOSED_ALGO * MAX_NAME_LEN, also
							   is the max length for a password etc */

/* For a 4096 bit DSS key, empirically determined to be 1590 bytes */
#define MAX_PUBKEY_SIZE 1600
/* For a 4096 bit DSS key, empirically determined to be 1590 bytes */
#define MAX_PRIVKEY_SIZE 1600

#define DROPBEAR_MAX_SOCKS 2 /* IPv4, IPv6 are all we'll get for now. Revisit
								in a few years time.... */

#ifndef ENABLE_X11FWD
#define DISABLE_X11FWD
#endif

#ifndef ENABLE_AGENTFWD
#define DISABLE_AGENTFWD
#endif

#ifndef ENABLE_LOCALTCPFWD
#define DISABLE_TCPDIRECT
#endif

#ifndef ENABLE_REMOTETCPFWD
#define DISABLE_REMOTETCPFWD
#endif

#if defined(ENABLE_CLI_REMOTETCPFWD) || defined(ENABLE_CLI_LOCALTCPFWD)
#define ENABLE_CLI_ANYTCPFWD 
#endif

#if defined(ENABLE_CLI_LOCALTCPFWD) || defined(ENABLE_SVR_REMOTETCPFWD)
#define DROPBEAR_TCP_ACCEPT
#endif

#if defined(ENABLE_REMOTETCPFWD) || defined(ENABLE_LOCALTCPFWD) || \
	defined(ENABLE_AGENTFWD) || defined(ENABLE_X11FWD)
#define USING_LISTENERS
#endif

#if defined(DROPBEAR_CLIENT) || defined(ENABLE_SVR_PUBKEY_AUTH)
#define DROPBEAR_KEY_LINES /* ie we're using authorized_keys or known_hosts */
#endif

/* We use dropbear_client and dropbear_server as shortcuts to avoid redundant
 * code, if we're just compiling as client or server */
#if defined(DROPBEAR_SERVER) && defined(DROPBEAR_CLIENT)

#define IS_DROPBEAR_SERVER (ses.isserver == 1)
#define IS_DROPBEAR_CLIENT (ses.isserver == 0)

#elif defined(DROPBEAR_SERVER)

#define IS_DROPBEAR_SERVER 1
#define IS_DROPBEAR_CLIENT 0

#elif defined(DROPBEAR_CLIENT)

#define IS_DROPBEAR_SERVER 0
#define IS_DROPBEAR_CLIENT 1

#else
#error You must compiled with either DROPBEAR_CLIENT or DROPBEAR_SERVER selected
#endif

#endif /* _OPTIONS_H_ */