| # Copyright 2010-2012 Free Software Foundation, Inc. |
| |
| # This program is free software; you can redistribute it and/or modify |
| # it under the terms of the GNU General Public License as published by |
| # the Free Software Foundation; either version 3 of the License, or |
| # (at your option) any later version. |
| # |
| # This program is distributed in the hope that it will be useful, |
| # but WITHOUT ANY WARRANTY; without even the implied warranty of |
| # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| # GNU General Public License for more details. |
| # |
| # You should have received a copy of the GNU General Public License |
| # along with this program. If not, see <http://www.gnu.org/licenses/>. */ |
| |
| # In some cases gdbserver cannot find the DT_DEBUG library list on its own and |
| # it needs to fall back to GDB solib-svr4.c look up via symbols from the main |
| # executable. |
| # gdbserver :1234 ld-linux-x86-64.so.2 /bin/prog |
| # gdb /bin/prog |
| # (gdb) target remote ... |
| |
| load_lib gdbserver-support.exp |
| load_lib prelink-support.exp |
| |
| if {[skip_gdbserver_tests] || [skip_shlib_tests]} { |
| return |
| } |
| |
| standard_testfile solib-list-main.c |
| set srclibfile ${testfile}-lib.c |
| set binlibfile [standard_output_file ${testfile}.so] |
| set executable ${testfile} |
| set objfile ${binfile}.o |
| |
| if { [get_compiler_info] |
| || [gdb_compile_shlib "${srcdir}/${subdir}/${srclibfile}" "${binlibfile}" [list debug ldflags=-Wl,-soname,${binlibfile}]] != "" |
| || [gdb_compile "${srcdir}/${subdir}/${srcfile}" "${objfile}" object {debug}] != "" |
| || [gdb_compile "${objfile} ${binlibfile}" "${binfile}" executable {}] != "" } { |
| untested "could not compile sources" |
| return -1 |
| } |
| |
| set interp_system [section_get ${binfile} .interp] |
| verbose -log "system interpreter is: $interp_system" |
| |
| foreach nonstop { 0 1 } { with_test_prefix "non-stop $nonstop" { |
| |
| # clean_restart assumes ${objdir}/${subdir}/ which is not applicable |
| # for ${interp_system}. |
| gdb_exit |
| gdb_start |
| gdb_reinitialize_dir $srcdir/$subdir |
| gdb_load ${interp_system} |
| gdb_load_shlibs ${binfile} |
| gdb_load_shlibs ${binlibfile} |
| |
| # Make sure we're disconnected, in case we're testing with an |
| # extended-remote board, therefore already connected. |
| gdb_test "disconnect" ".*" |
| |
| gdb_test "set non-stop $nonstop" |
| gdb_test "set target-async $nonstop" |
| |
| # It is required for the non-stop mode, GDB would try to step over |
| # _dl_debug_state breakpoint will still only ld.so loaded in gdbserver. |
| # But GDB having symbols from the main executable it would try to use |
| # displaced-stepping buffer at unmapped that time address _start. |
| gdb_test "set displaced-stepping off" |
| |
| set res [gdbserver_spawn ${binfile}] |
| set gdbserver_protocol [lindex $res 0] |
| set gdbserver_gdbport [lindex $res 1] |
| |
| # Load BINFILE after gdbserver_spawn (so that gdbserver executes ld.so) |
| # but before "target remote" below so that qSymbol data get already |
| # initialized from BINFILE (and not from ld.so first needing a change to |
| # BINFILE later). |
| gdb_test "file ${binfile}" {Reading symbols from .*\.\.\.done\..*} "file binfile" \ |
| {(Are you sure you want to change the file|Load new symbol table from ".*")\? \(y or n\) } "y" |
| |
| set test "target $gdbserver_protocol" |
| gdb_test_multiple "target $gdbserver_protocol $gdbserver_gdbport" $test { |
| -re "Remote debugging using .*\r\n$gdb_prompt " { |
| # Do not anchor end, there may be more output in non-stop mode. |
| pass $test |
| } |
| } |
| |
| if $nonstop { |
| set test "non-stop interior stop" |
| gdb_test_multiple "" $test { |
| -re " #1 stopped\\.\r\n" { |
| pass $test |
| } |
| } |
| } |
| |
| gdb_test "continue" "Program received signal SIGUSR1, .*" |
| gdb_test "sharedlibrary" ".*" |
| gdb_test "p libvar" " = 23" |
| }} |