| # |
| # These tests should be valid on all targets. |
| # |
| |
| # I think currently all targets fail this one when listings are enabled. |
| gas_test "p2425.s" "" "" "pcrel values in assignment" |
| |
| # p1480.s uses a ".space" directive which for most assemblers means |
| # "allocate some space". On the PA it means "switch into this space". |
| # |
| # Therefore this test (as it is currently written) is completely bogus |
| # for any PA target. Do not bother trying to run it and just claim |
| # it fails. |
| # |
| # The C54x uses ".space" to allocate bits, and requires absolute expressions; |
| # The ".space" directive is taken care of in the C54x-specific tests, so fail |
| # here |
| # |
| if { [istarget hppa*-*-*] || [istarget *c54x*-*-*] } then { |
| setup_xfail *-*-* |
| fail "simplifiable double subtraction" |
| } else { |
| gas_test "p1480.s" "" "-a>" "simplifiable double subtraction" |
| } |
| |
| # No floating point support in assembly code for CRIS. |
| if ![istarget cris-*-*] then { |
| gas_test "float.s" "" "" "simple FP constants" |
| } |
| |
| # This test is meaningless for the PA; the difference of two undefined |
| # symbols is something that is (and must be) supported on the PA. |
| if ![istarget hppa*-*-*] then { |
| gas_test_error "diff1.s" "" "difference of two undefined symbols" |
| } |
| |
| proc do_comment {} { |
| set testname "comment.s: comments in listings" |
| set x1 0 |
| set x2 0 |
| set x3 0 |
| set white {[ \t]*} |
| gas_start "comment.s" "-al" |
| while 1 { |
| # Apparently CRLF is received when using ptys for subprocesses; hence the |
| # \r\n for line 3. |
| expect { |
| -re "^ +1\[ \t\]+# This\[^\n\]*\n" { set x1 1 } |
| -re "^ +2\[ \t\]+# correctly\[^\n\]*\n" { set x2 1 } |
| -re "^ +3\[ \t\]+/. C comments too. ./\r?\n" { set x3 1 } |
| -re "\[^\n\]*\n" { } |
| timeout { perror "timeout\n"; break } |
| eof { break } |
| } |
| } |
| gas_finish |
| if [all_ones $x1 $x2 $x3] then { pass $testname } else { fail $testname } |
| } |
| |
| do_comment |
| |
| # |
| # Test x930509a -- correct assembly of differences involving forward |
| # references. |
| # |
| |
| proc do_930509a {} { |
| set testname "difference between forward references" |
| set x 0 |
| gas_start "x930509.s" "-al" |
| while 1 { |
| # We need to accomodate both byte orders here. |
| # If ".long" means an 8-byte value on some target someday, this test will have |
| # to be fixed. |
| expect { |
| -re "^ +1 .... 00 ?00 ?00 ?00" { fail $testname; set x 1 } |
| -re "^ +1 .... 04 ?00 ?00 ?00" { pass $testname; set x 1 } |
| -re "^ +1 .... 00 ?00 ?00 ?04" { pass $testname; set x 1 } |
| -re "\[^\n\]*\n" { } |
| timeout { perror "timeout\n"; break } |
| eof { break } |
| } |
| } |
| gas_finish |
| if !$x then { fail $testname } |
| } |
| |
| # This test is meaningless for the PA; the difference of two symbols |
| # must not be resolved by the assembler. |
| # C54x assembler (for compatibility) does not allow differences between |
| # forward references |
| if { ![istarget hppa*-*-*] && ![istarget *c54x*-*-*] } then { |
| # the vax fails because VMS can apparently actually handle this |
| # case in relocs, so gas doesn't handle it itself. |
| setup_xfail "vax*-*-vms*" |
| setup_xfail "mn10300*-*-*" |
| setup_xfail "mn10200*-*-*" |
| do_930509a |
| } |
| |
| # ".struct" and ".align" have different meanings on c54x |
| # These directives are done in the c54x-specific tests instead |
| case $target_triplet in { |
| { hppa*-*-* } { } |
| { *c54x*-*-* } { } |
| default { |
| run_dump_test struct |
| run_dump_test align |
| } |
| } |
| |
| # This test is for any COFF target. |
| # We omit m88k COFF because it uses weird pseudo-op names. |
| # We omit the ARM toolchains because they define locals to |
| # start with '.', which eliminates .eos, .text etc from the output. |
| # Omit c54x, since .tag and .def mean something different on that target |
| if { ([istarget *-*-coff*] && ![istarget m88*-*-*] && ![istarget *arm*-*-coff] && ![istarget thumb*-*-coff] && ![istarget *c54x*-*-coff]) \ |
| ||([istarget *-*-pe*] && ![istarget arm*-*-pe*] && ![istarget thumb*-*-pe*]) \ |
| || [istarget a29k-*-udi*] \ |
| || [istarget a29k-*-ebmon*] \ |
| || [istarget a29k-*-sym*] \ |
| || [istarget a29k-*-vxworks*] \ |
| || [istarget i*86-*-aix*] \ |
| || [istarget i*86-*-sco*] \ |
| || [istarget i*86-*-isc*] \ |
| || [istarget i*86-*-go32*] \ |
| || [istarget i*86-*-cygwin*] \ |
| || [istarget i*86-*-*nt] \ |
| || [istarget i*86-*-interix*] \ |
| || ([istarget i960-*-vxworks5.*] && ![istarget i960-*-vxworks5.0*]) } { |
| run_dump_test cofftag |
| } |
| |
| # Test omitting conditionals from listings. |
| proc test_cond {} { |
| global comp_output |
| global srcdir |
| global subdir |
| |
| set testname "conditional listings" |
| gas_run cond.s "-alc" ">dump.out" |
| if ![string match "" $comp_output] { |
| send_log "$comp_output\n" |
| fail $testname |
| } else { |
| if { [regexp_diff dump.out $srcdir/$subdir/cond.d] } { |
| fail $testname |
| } else { |
| pass $testname |
| } |
| } |
| } |
| |
| # again, p2align doesn't work on c54x target |
| if ![istarget *c54x*-*-*] then { |
| test_cond |
| } |
| |
| # FIXME: this is here cause of a bug in DejaGnu 1.1.1. When it is no longer |
| # in use, then this can be removed. |
| if [info exists errorInfo] then { |
| unset errorInfo |
| } |