| #!/system/bin/sh | |
| # | |
| # Copyright (C) 2017 The Android Open Source Project | |
| # | |
| # Licensed under the Apache License, Version 2.0 (the "License"); | |
| # you may not use this file except in compliance with the License. | |
| # You may obtain a copy of the License at | |
| # | |
| # http://www.apache.org/licenses/LICENSE-2.0 | |
| # | |
| # Unless required by applicable law or agreed to in writing, software | |
| # distributed under the License is distributed on an "AS IS" BASIS, | |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. | |
| # See the License for the specific language governing permissions and | |
| # limitations under the License. | |
| # | |
| # This script will extract ASAN libraries from /system/asan.tar.gz to /data and then reboot. | |
| # TODO: | |
| # * Timestamp or something to know when to run this again. Right now take the existence of | |
| # /data/lib as we're already done. | |
| # * Need to distinguish pre- from post-decryption for FDE. | |
| SRC=/system/asan.tar.bz2 | |
| MD5_FILE=/data/asan.md5sum | |
| ASAN_DIR=/data/asan | |
| # Minimum /data size in blocks. Arbitrarily 512M. | |
| MIN_DATA_SIZE=131072 | |
| # Checks for FDE pre-decrypt state. | |
| VOLD_STATUS=$(getprop vold.decrypt) | |
| if [ "$VOLD_STATUS" = "trigger_restart_min_framework" ] ; then | |
| log -p i -t asan_install "Pre-decrypt FDE detected (by vold property)!" | |
| exit 1 | |
| fi | |
| STATFS_BLOCKS=$(stat -f -c '%b' /data) | |
| if [ "$STATFS_BLOCKS" -le "$MIN_DATA_SIZE" ] ; then | |
| log -p i -t asan_install "Pre-decrypt FDE detected (by /data size)!" | |
| exit 1 | |
| fi | |
| # Check for ASAN source. | |
| if ! test -f $SRC ; then | |
| log -p i -t asan_install "Did not find $SRC!" | |
| exit 1 | |
| fi | |
| log -p i -t asan_install "Found $SRC, checking whether we need to apply it." | |
| # Checksum check. | |
| ASAN_TAR_MD5=$(md5sum $SRC) | |
| if test -f $MD5_FILE ; then | |
| INSTALLED_MD5=$(cat $MD5_FILE) | |
| if [ "x$ASAN_TAR_MD5" = "x$INSTALLED_MD5" ] ; then | |
| log -p i -t asan_install "Checksums match, nothing to be done here." | |
| exit 0 | |
| fi | |
| fi | |
| # Actually apply the source. | |
| # Just clean up, helps with restorecon. | |
| rm -rf $ASAN_DIR | |
| log -p i -t asan_install "Untarring $SRC..." | |
| # Unzip from /system/asan.tar.gz into data. Need to pipe as gunzip is not on device. | |
| bzip2 -c -d $SRC | tar -x -f - --no-same-owner -C / || exit 1 | |
| # Cannot log here, log would run with system_data_file. | |
| # Set correct permission bits. | |
| chmod -R 744 $ASAN_DIR | |
| cd $ASAN_DIR ; find . -type d -exec chmod 755 {} \; | |
| restorecon -R -F $ASAN_DIR/*/lib* | |
| log -p i -t asan_install "Fixed selinux labels..." | |
| # Now write down our checksum to mark the extraction complete. | |
| echo "$ASAN_TAR_MD5" > $MD5_FILE | |
| # We want to reboot now. It seems it is not possible to run "reboot" here, the device will | |
| # just be stuck. | |
| log -p i -t asan_install "Signaling init to reboot..." | |
| setprop sys.powerctl reboot |