// Copyright 2019 The Fuchsia Authors. All rights reserved.
// Use of this source code is governed by a BSD-style license that can be
// found in the LICENSE file.
library fuchsia.hardware.dsiimpl;
using zx;

/// This enum is used to configure DSI interface in either Video or Command mode
type DsiMode = strict enum : uint8 {
    VIDEO = 0;
    COMMAND = 1;
};

// This enum is used to configure the type of video mode
type VideoMode = strict enum : uint8 {
    NON_BURST_PULSE = 0;
    NON_BURST_EVENT = 1;
    BURST = 2;
};

// Supported color codes for the DSI interface
type ColorCode = strict enum : uint8 {
    PACKED_16BIT_565 = 0;
    PACKED_18BIT_666 = 1;
    LOOSE_24BIT_666 = 2;
    PACKED_24BIT_888 = 3;
};

/// This structure is populated based on hardware/lcd type. Its values come from vendor.
/// This table is the top level structure used to populated all DSI configuration registers
type DisplaySetting = struct {
    lane_num uint32;
    bit_rate_max uint32;
    lcd_clock uint32;
    h_active uint32;
    v_active uint32;
    h_period uint32;
    v_period uint32;
    hsync_width uint32;
    hsync_bp uint32;
    hsync_pol uint32;
    vsync_width uint32;
    vsync_bp uint32;
    vsync_pol uint32;
};

/// This structure contains designware specific data
type DesignwareConfig = struct {
    lp_escape_time uint32;
    lp_cmd_pkt_size uint32;
    phy_timer_clkhs_to_lp uint32;
    phy_timer_clklp_to_hs uint32;
    phy_timer_hs_to_lp uint32;
    phy_timer_lp_to_hs uint32;
    auto_clklane uint8;
};

/// This structure contains information that the DSI block needs from the MIPI D-PHY
type DsiConfig = struct {
    display_setting DisplaySetting;
    video_mode_type VideoMode;
    color_coding ColorCode;
    @buffer
    @mutable
    vendor_config vector<uint8>:MAX;
};

/// This is the generic MIPI-DSI command structure
type MipiDsiCmd = struct {
    virt_chn_id uint8;
    dsi_data_type uint8;

    // TX Direction
    pld_data vector<uint8>:MAX;

    // RX Direction
    @mutable
    rsp_data vector<uint8>:MAX;

    flags uint32;
};

@transport("Banjo")
@banjo_layout("ddk-protocol")
closed protocol DsiImpl {
    /// This function is used to configure all the DSI parameters needed to operated in both
    /// Command and Video Mode
    strict Config(struct {
        dsi_config DsiConfig;
    }) -> (struct {
        s zx.Status;
    });
    /// This function is called to power up the DSI interface
    strict PowerUp() -> ();
    /// This function is called to power down the DSI interface
    strict PowerDown() -> ();
    /// This function is used to change modes between Video and Command.
    strict SetMode(struct {
        mode DsiMode;
    }) -> ();
    /// This function is used to send a MIPI-DSI command through the DSI block
    strict SendCmd(struct {
        cmd vector<MipiDsiCmd>:MAX;
    }) -> (struct {
        s zx.Status;
    });

    /// This function is used to power up the MIPI D-PHY block
    strict PhyPowerUp() -> ();
    /// This function is used to power up the MIPI D-PHY block
    strict PhyPowerDown() -> ();
    /// This function is used to communicate the MIPI D-PHY
    strict PhySendCode(struct {
        code uint32;
        parameter uint32;
    }) -> ();
    /// This function checks two things in order to decide whether the PHY is
    /// ready or not. LOCK Bit and StopStateClk bit. According to spec, once these
    /// are set, PHY has completed initialization
    strict PhyWaitForReady() -> (struct {
        s zx.Status;
    });
};