// Copyright 2020 The Fuchsia Authors. All rights reserved.
// Use of this source code is governed by a BSD-style license that can be
// found in the LICENSE file.

/// Defines the protocols used to sample UTC time using time synchronization
/// protocols such as NTP.
///
/// New time protocols may be added to the system by implementing the server
/// side of one or more of these protocols. The core timekeeper system acts as
/// the client and uses produced samples to update the system time.
///
/// Implementing PushSource is preferred, as it allows the server to decide when
/// to produce samples. The server has knowledge of the particular protocol it
/// understands and is therefore better informed when to produce a timesample.
///
/// UTC time is distributed by the system. Clients that need to obtain UTC time
/// should use the standard libraries provided by their runtime.
library fuchsia.time.external;
using zx;

/// A protocol which defines common methods for all time sources. Should not be
/// implemented directly.
protocol TimeSource {
    /// Notifies the time source of changes to global properties of the device
    /// that it may use to increase accuracy of time measurements.
    UpdateDeviceProperties(Properties properties);
};

/// A protocol for time sources that produce time samples on demand.
[Discoverable]
protocol PullSource {
    compose TimeSource;
    /// Produce a new time sample.
    ///
    /// Returns a RATE_LIMITED error if the client should wait before requesting
    /// another sample. For example, this can occur if a server requests that the
    /// source make less frequent requests. In this case, the client should call
    /// `NextSampleTime` to retrieve the next time it may request a sample.
    Sample() -> (TimeSample sample) error Error;

    /// Returns the monotonic time at which the PullSource is willing to produce
    /// another sample. If the PullSource is not rate limited it may return the
    /// current monotonic time or earlier.
    NextPossibleSampleTime() -> (zx.time next_possible_time);
};

/// A protocol for time sources that produce time samples on a schedule that it
/// dictates. A PushSource does not report errors to clients as it is responsible
/// for handling them internally. Instead, a PushSource reports a general health
/// indication through the `WatchHealth` method to reflect whether or not it
/// expects to successfully produce time samples.
[Discoverable]
protocol PushSource {
    compose TimeSource;
    /// Watch for new time samples from the time source. This method is a hanging
    /// get and returns the latest time sample if one is available and has not
    /// already been returned to the client. If no such sample is available, the
    /// method will hang until one is produced and return it then.
    ///
    /// Note that it is entirely at the discretion of the PushSource
    /// implementation when to produce a sample and a call to WatchSample does
    /// not necessarily trigger sample collection.
    ///
    /// In the case a client sends a second WatchSample request while another
    /// request is active, the channel is closed with a ZX_ERR_BAD_STATE
    /// epitaph.
    WatchSample() -> (TimeSample sample);

    /// Watch for changes in the status of the time source.
    ///
    /// This method is a hanging get that returns when the status changes from
    /// the last status reported to the client.
    ///
    /// In the case a client sends a second WatchStatus request while another
    /// request is active, the channel is closed with a ZX_ERR_BAD_STATE
    /// epitaph.
    WatchStatus() -> (Status status);
};

/// A correspondence pair that describes a UTC time and the monotonic time at
/// which the time was measured.
table TimeSample {
    /// The UTC time sample. Must always be provided.
    1: zx.time utc;
    /// The monotonic time at which the sample was most valid. Must always be provided.
    2: zx.time monotonic;
    /// The standard deviation representing the error distribution of the UTC measurement.
    /// Must always be provided.
    3: zx.duration standard_deviation;
};

/// Enum of states a PullSource may be in.
enum Status {
    /// The time source is performing setup steps or waiting for dependencies such
    /// as network to become available.
    INITIALIZING = 0;
    /// The time source is healthy and expects to produce time samples.
    OK = 1;
    /// The time source does not expect to produce time samples for reasons that
    /// cannot be classified as one of the more specific statuses.
    UNKNOWN_UNHEALTHY = 2;
    /// The time source is unable to produce time samples due to network availability
    /// issues.
    NETWORK = 3;
    /// The time source is unable to produce time samples due to hardware issues.
    HARDWARE = 4;
    /// The time source is unable to produce time samples due to errors specific to
    /// the implemented time protocol.
    PROTOCOL = 5;
    /// The time source is unable to produce time samples due to local resource errors
    /// such as IO, FIDL, or memory allocation.
    RESOURCE = 6;
};

/// Enum of reasons why producing a time sample failed.
enum Error {
    /// An error occurred that cannot be classified as one of the more specific
    /// error statuses.
    UNKNOWN = 1;
    /// An internal error occurred. This usually indicates a bug in the
    /// component implementation.
    INTERNAL = 2;
    /// A local resource error occurred such as IO, FIDL, or memory allocation
    /// failure.
    RESOURCE = 3;
    /// A network error occurred.
    NETWORK = 4;
    /// Some hardware that the time source depends on failed.
    HARDWARE = 5;
    /// A retriable error specific to the implemented time protocol occurred, such
    /// as a malformed response from a remote server.
    PROTOCOL = 6;
    /// Sampling failed in a nonretriable way. Examples include failed
    /// authentication, or a missing configuration.
    PROTOCOL_UNRECOVERABLE = 7;
    /// The request was made too soon and the client should wait before making
    /// another request.
    RATE_LIMITED = 8;
};

/// Device global properties a time source may use to help it sample time.
table Properties {
};