sdk/banjo/fuchsia.hardware.dsiimpl/dsiimpl.banjo

// Copyright 2019 The Fuchsia Authors. All rights reserved.
// Use of this source code is governed by a BSD-style license that can be
// found in the LICENSE file.

library fuchsia.hardware.dsiimpl;
using zx;

/// This enum is used to configure DSI interface in either Video or Command mode
enum DsiMode : uint8 {
    VIDEO = 0;
    COMMAND = 1;
};

// This enum is used to configure the type of video mode
enum VideoMode : uint8 {
    NON_BURST_PULSE = 0;
    NON_BURST_EVENT = 1;
    BURST = 2;
};

// Supported color codes for the DSI interface
enum ColorCode : uint8 {
    PACKED_16BIT_565 = 0;
    PACKED_18BIT_666 = 1;
    LOOSE_24BIT_666 = 2;
    PACKED_24BIT_888 = 3;
};

/// This structure is populated based on hardware/lcd type. Its values come from vendor.
/// This table is the top level structure used to populated all DSI configuration registers
struct DisplaySetting {
    uint32 lane_num;
    uint32 bit_rate_max;
    uint32 clock_factor;
    uint32 lcd_clock;
    uint32 h_active;
    uint32 v_active;
    uint32 h_period;
    uint32 v_period;
    uint32 hsync_width;
    uint32 hsync_bp;
    uint32 hsync_pol;
    uint32 vsync_width;
    uint32 vsync_bp;
    uint32 vsync_pol;
};

/// This structure contains designware specific data
struct DesignwareConfig {
    uint32 lp_escape_time;
    uint32 lp_cmd_pkt_size;
    uint32 phy_timer_clkhs_to_lp;
    uint32 phy_timer_clklp_to_hs;
    uint32 phy_timer_hs_to_lp;
    uint32 phy_timer_lp_to_hs;
    uint8 auto_clklane;
};

/// This structure contains information that the DSI block needs from the MIPI D-PHY
struct DsiConfig {
    DisplaySetting display_setting;
    VideoMode video_mode_type;
    ColorCode color_coding;
    [Buffer, Mutable] vector<uint8> vendor_config;
};

/// This is the generic MIPI-DSI command structure
struct MipiDsiCmd {
    uint8 virt_chn_id;
    uint8 dsi_data_type;

    // TX Direction
    vector<uint8> pld_data;

    // RX Direction
    [Mutable] vector<uint8> rsp_data;

    uint32 flags;
};

[BanjoLayout = "ddk-protocol"]
protocol DsiImpl {
    /// This function is used to configure all the DSI parameters needed to operated in both
    /// Command and Video Mode
    Config(DsiConfig dsi_config) -> (zx.status s);
    /// This function is called to power up the DSI interface
    PowerUp() -> ();
    /// This function is called to power down the DSI interface
    PowerDown() -> ();
    /// This function is used to change modes between Video and Command.
    SetMode(DsiMode mode) -> ();
    /// This function is used to send a MIPI-DSI command through the DSI block
    SendCmd(vector<MipiDsiCmd> cmd) -> (zx.status s);
    /// This function return true if the DSI block is powered on and not in reset
    IsPoweredUp() -> (bool on);
    /// This function resets the DSI IP block
    Reset() -> ();

    /// This function configures the PHY IP (inf within the DSI block)
    PhyConfig(DsiConfig dsi_config) -> (zx.status s);
    /// This function is used to power up the MIPI D-PHY block
    PhyPowerUp() -> ();
    /// This function is used to power up the MIPI D-PHY block
    PhyPowerDown() -> ();
    /// This function is used to communicate the MIPI D-PHY
    PhySendCode(uint32 code, uint32 parameter) -> ();
    /// This function checks two things in order to decide whether the PHY is
    /// ready or not. LOCK Bit and StopStateClk bit. According to spec, once these
    /// are set, PHY has completed initialization
    PhyWaitForReady() -> (zx.status s);

    /// This function allows writing to any register within the DSI block. This could be used
    /// for debug purposes during development stages without needing to modify the DSI IMPL
    /// protocol or to write to registers that don't really belong in the DSI IP block.
    WriteReg(uint32 reg, uint32 val) -> (zx.status s);

    /// This function returns the value of any register within the DSI IP block
    ReadReg(uint32 reg) -> (zx.status s, uint32 val);

    /// This function enable BIST pattern generation. This is useful during development stages
    EnableBist(uint32 pattern) -> (zx.status s);

    /// This function prints the value of all DSI registers
    PrintDsiRegisters() -> ();
};