Pink + Purple == Fuchsia (a new Operating System)
Welcome to Fuchsia! This document has everything you need to get started with Fuchsia.
sudo apt-get install build-essential curl git python unzip
Install Command Line Tools:
xcode-select --install
In addition to Command Line Tools, you also need to install a recent version of Xcode.
Follow the instructions to get the Fuchsia source and then return to this document.
Note: A quick overview of the basic build-and-pave workflow can be found here.
If you added .jiri_root/bin
to your path as part of getting the source code, the fx
command should already be in your path. If not, the command is also available as scripts/fx
.
fx set core.x64 --with //bundles:kitchen_sink fx build
The first command selects the build configuration you wish to build and generates the build system itself in an output directory (e.g., out/x64
). Fuchsia can ephemerally download packages over the network; here we use the --available
flag to make the necessary packages covered in this guide available for download.
The second command actually executes the build, transforming the source code in build products. If you modify the source tree, you can do an incremental build by re-running the fx build
command alone. fx -i build
starts a watcher and automatically builds whenever a file is changed.
Alternatively, you can use the underlying build system directly.
By default you will get a x64 debug build. You can skip this section unless you want something else.
Run fx set
to see a list of build options. Some examples:
fx set workstation.x64 # x64 debug build fx set core.arm64 # arm64 debug build fx set core.x64 --release # x64 release build
ccache
and goma
ccache
accelerates builds by caching artifacts from previous builds. ccache
is enabled automatically if the CCACHE_DIR
environment variable is set and refers to a directory that exists.
[Googlers only: goma
accelerates builds by distributing compilation across many machines. If you have goma
installed in ~/goma
, it is used by default. It is also used by default in preference to ccache
.]
To override the default behaviors, pass flags to fx set
:
--ccache # force use of ccache even if goma is available --no-ccache # disable use of ccache --no-goma # disable use of goma
To get Fuchsia running on hardware requires using the paver, which these instructions will help you get up and running with.
Note: A quick overview of the basic build-and-pave workflow can be found here.
If you don't have the supported hardware, you can run Fuchsia under emulation using QEMU. Fuchsia includes prebuilt binaries for QEMU under buildtools/qemu
.
The fx run
command will launch Zircon within QEMU, using the locally built disk image:
fx run
There are various flags for fx run
to control QEMU's configuration:
-m
sets QEMU's memory size in MB.-g
enables graphics (see below).-N
enables networking (see below).-k
enables KVM acceleration on Linux.Use fx run -h
to see all available options.
ctrl+a x
will exit QEMU in text mode.ctrl+a ?
or ctrl+a h
prints all supported commands.Note: Graphics under QEMU are extremely limited due to a lack of Vulkan support. Only the Zircon UI renders.
To enable graphics under QEMU, add the -g
flag to fx run
:
fx run -g
First, configure a virtual interface for QEMU's use.
Once this is done you can add the -N
and -u
flags to fx run
:
fx run -N -u scripts/start-dhcp-server.sh
The -u
flag runs a script that sets up a local DHCP server and NAT to configure the IPv4 interface and routing.
In a separate shell, start the development update server, if it isn't already running:
fx serve -v
Boot Fuchsia with networking. This can be done either in QEMU via the -N
flag, or on a paved hardware, both described above. When Fuchsia has booted and displays the “$” shell prompt, you can run programs!
For example, to receive deep wisdom, run:
fortune
To shutdown or reboot Fuchsia, use the dm
command:
dm help dm shutdown
Almost everything that exists on a Fuchsia system is stored in a Fuchsia package. A typical development workflow involves re-building and pushing Fuchsia packages to a development device or QEMU virtual device.
Make a change to the rolldice binary in garnet/bin/rolldice/src/main.rs
.
Re-build and push the rolldice package to a running Fuchsia device with:
fx build-push rolldice
From a shell prompt on the Fuchsia device, run the updated rolldice component with:
rolldice
Fuchsia shows multiple tabs after booting with graphics enabled. The currently selected tab is highlighted in yellow at the top of the screen. You can switch to the next tab using Alt-Tab on the keyboard.
Note: to select tabs, you may need to enter “console mode”. See the next section for details.
QEMU does not support Vulkan and therefore cannot run our graphics stack.
Most graphical components in Fuchsia use the Scenic system compositor. You can launch such components, commonly found in /system/apps
, like this:
launch spinning_square_view
Source code for Scenic example apps is here.
When you launch something that uses Scenic, uses hardware-accelerated graphics, or if you build the default package (which will boot into the Fuchsia System UI), Fuchsia will enter “graphics mode”, which will not display any of the text shells. In order to use the text shell, you will need to enter “console mode” by pressing Alt-Escape. In console mode, Alt-Tab will have the behavior described in the previous section, and pressing Alt-Escape again will take you back to the graphical shell.
If you would like to use a text shell inside a terminal emulator from within the graphical shell you can launch the term by selecting the “Ask Anything” box and typing moterm
.
Compiled test binaries are installed in /pkgfs/packages/
, and are referenced by a URI. You can run a test by invoking it in the terminal. E.g.
run fuchsia-pkg://fuchsia.com/ledger_tests#meta/ledger_unittests.cmx
If you want to leave Fuchsia running and recompile and re-run a test, run Fuchsia with networking enabled in one terminal, then in another terminal, run:
fx run-test <test name> [<test args>]
You may wish to peruse the testing FAQ.